Texas Instruments X-Loader 1.5.1 (Aug 16 2012 - 15:36:52) Beagle Rev C5 Reading boot sector Loading u-boot.bin from mmc U-Boot 2010.06-dirty (Aug 17 2012 - 11:28:39) OMAP3430/3530-GP ES3.1, CPU-OPP2 L3-165MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: HW ECC [Kernel/FS layout] selected 512 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Beagle Rev C4 Die ID #10c80004000000000403951c0a021016 Hit any key to stop autoboot: 0 OMAP3 beagleboard.org # nandecc sw SW ECC selected OMAP3 beagleboard.org # nand erase 0 0x20000000 NAND erase: device 0 whole chip Erasing at 0x1ffe0000 -- 100% complete. OK OMAP3 beagleboard.org # boot mmc1 is available reading boot.scr ** Unable to read "boot.scr" from mmc 0:1 ** reading uImage 3583320 bytes read Booting from mmc ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-2.6.37-g304ec32-dirty Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3583256 Bytes = 3.4 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.37-g304ec32-dirty (test@lucid1004clnoeandroidubifs) (gcc version 4.4.3 (GCC) ) #38 Fri Aug 17 10:58:45 MYT 2012 CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 Beagle Board Reserving 12582912 bytes SDRAM for VRAM Memory policy: ECC disabled, Data cache writeback OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720mhz ) SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61952 Kernel command line: console=ttyO2,115200n8 androidboot.console=ttyO2 mem=256M init=/init mpurate=720 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 244MB = 244MB total Memory: 239492k/239492k available, 22652k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc003c000 ( 208 kB) .text : 0xc003c000 - 0xc06c7000 (6700 kB) .data : 0xc06c8000 - 0xc0718c00 ( 323 kB) NR_IRQS:409 Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz Reprogramming SDRC clock to 332000000 Hz IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller GPMC revision 5.0 Trying to install interrupt handler for IRQ402 Trying to install interrupt handler for IRQ403 Trying to install interrupt handler for IRQ404 Trying to install interrupt handler for IRQ405 Trying to install interrupt handler for IRQ406 Trying to install interrupt handler for IRQ407 Trying to install interrupt handler for IRQ408 Trying to install type control for IRQ409 Trying to set irq flags for IRQ409 OMAP clockevent source: GPTIMER1 at 32768 Hz Console: colour dummy device 80x30 Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok regulator: core version 0.5 regulator: dummy: NET: Registered protocol family 16 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 omap_mux_init: Add partition: #1: core, flags: 0 OMAP3 Beagle Rev: C4 Found NAND on CS0 Registering NAND on CS0 Unable to get DVI reset GPIO hw-breakpoint: debug architecture 0x4 unsupported. Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/720 MHz OMAP DMA hardware revision 4.0 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 regulator: VUSB1V5: 1500 mV normal standby regulator: VUSB1V8: 1800 mV normal standby regulator: VUSB3V1: 3100 mV normal standby twl4030_usb twl4030_usb: Initialized TWL4030 USB module regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby regulator: VDAC: 1800 mV normal standby regulator: VDVI: 1800 mV normal standby regulator: VMMC2: at 2600 mV regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby regulator: VAUX3: 1800 mV normal standby regulator: VAUX4: 1800 mV normal standby omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz Advanced Linux Sound Architecture Driver Version 1.0.23. Bluetooth: Core ver 2.15 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Switching to clocksource 32k_counter musb-hdrc: version 6.0, otg (peripheral+host), debug=0 musb-hdrc musb-hdrc.0: dma type: dma-inventra musb-hdrc musb-hdrc.0: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. NetWinder Floating Point Emulator V0.97 (double precision) platform iva.0: Enabled OPP corresponding to 720MHz omap-iommu omap-iommu.0: isp registered OMAP35x Linux PSP version 04.02.00.07 (OMAP3BEAGLE) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. msgmni has been set to 467 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 OMAP DSI rev 1.0 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled sc16is7xx_init: enter sc16is7xx-uart: version 1.0 omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 console [ttyO2] enabled brd: module loaded loop: module loaded mtdoops: mtd device (mtddev=name/number) must be supplied omap2-nand driver initializing NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron ) Creating 5 MTD partitions on "omap2-nand.0": 0x000000000000-0x000000080000 : "X-Loader" 0x000000080000-0x000000260000 : "U-Boot" 0x000000260000-0x000000280000 : "U-Boot Env" 0x000000280000-0x000000780000 : "Kernel" 0x000000780000-0x000020000000 : "File System" OneNAND driver initializing usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap.0 supply hsusb0 not found, using dummy regulator ehci-omap.0 supply hsusb1 not found, using dummy regulator ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OMAP-EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.37-g304ec32-dirty ehci_hcd usb usb1: SerialNumber: ehci-omap.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. android init android_probe pdata: c06d862c android_bind android_usb gadget: android_usb ready musb-hdrc musb-hdrc.0: MUSB HDRC host driver musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: MUSB HDRC host driver usb usb2: Manufacturer: Linux 2.6.37-g304ec32-dirty musb-hcd usb usb2: SerialNumber: musb-hdrc.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected f_adb init android_register_function adb f_mass_storage init fsg_probe pdev: c06d8458, pdata: c06d8684 android_register_function usb_mass_storage adb_bind_config android_usb gadget: Mass Storage Function, version: 2009/09/11 android_usb gadget: Number of LUNs=1 lun0: LUN: removable file: (no medium) mice: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys/input/input0 input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 using rtc device, twl_rtc, for alarms twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 twl_rtc twl_rtc: Power up reset detected. twl_rtc twl_rtc: Enabling TWL-RTC. i2c /dev entries driver Linux media interface: v0.10 Linux video capture interface: v2.00 omap3isp supply VDD_CSIPHY1 not found, using dummy regulator omap3isp supply VDD_CSIPHY2 not found, using dummy regulator omap3isp omap3isp: Revision 2.0 found omap-iommu omap-iommu.0: isp: version 1.1 omap_i2c omap_i2c.2: controller timed out mt9v113 2-003c: chip id mismatch read 0x0, expecting 0x2280 isp_register_subdev_group: Unable to register subdev mt9v113 usbcore: registered new interface driver uvcvideo USB Video Class driver (v1.0.0) OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec twl4030_wdt twl4030_wdt: Failed to register misc device twl4030_wdt: probe of twl4030_wdt failed with error -16 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@redhat.com Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCILL protocol initialized Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0 mmci-omap-hs.1 supply vmmc_aux not found, using dummy regulator usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' usbcore: registered new interface driver snd-usb-audio OMAP3 Beagle/Devkit8000 SoC init asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok ALSA device list: #0: omap3beagle oprofile: hardware counters not available oprofile: using timer interrupt. nf_conntrack version 0.5.0 (3742 buckets, 14968 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Bluetooth: L2CAP ver 2.15 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 Registering the dns_resolver key type VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 ThumbEE CPU extension supported. Power Management for TI OMAP3. smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized SmartReflex Class3 initialized clock: disabling unused clocks to save power platform l3_main.0: omap_voltage_scale: Already at the requestedrate 166000000 platform iva.0: omap_voltage_scale: Already at the requestedrate 430000000 platform mpu.0: omap_voltage_scale: Already at the requestedrate 600000000 platform l3_main.0: omap_voltage_scale: Already at the requestedrate 166000000 fbcvt: 1024x768@60: CVT Name - .786M3-R regulator_init_complete: incomplete constraints, leaving VDAC on twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) Waiting for root device /dev/mmcblk0p2... mmc0: new SD card at address aaaa mmcblk0: mmc0:aaaa SU02G 1.84 GiB mmcblk0: p1 p2 p3 regulator_check_voltage: operation not allowed for VMMC2 mmci-omap-hs mmci-omap-hs.1: could not set regulator OCR (-1) EXT4-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. Freeing init memory: 208K init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead. Compat-wireless backport release: compat-wireless-2011-12-05-1-g84dbe2c Backport based on wl12xx.git v2.6.39-1328-g0890f48 cfg80211: Calling CRDA to update world regulatory domain init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' cfg80211: World regulatory domain updated: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) enabling adb adb_open root@android:/ # root@android:/ # cd /mtdtest/ root@android:/mtdtest # cat /proc/mtd dev: size erasesize name mtd0: 00080000 00020000 "X-Loader" mtd1: 001e0000 00020000 "U-Boot" mtd2: 00020000 00020000 "U-Boot Env" mtd3: 00500000 00020000 "Kernel" mtd4: 1f880000 00020000 "File System"