U-Boot SPL 2018.09-00002-g0b54a51eee (Sep 10 2018 - 19:41:39 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2018.09-00002-g0b54a51eee (Sep 10 2018 - 19:41:39 -0500), Build: jenkins-github_Bootloader-Builder-65 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds board_name=[A335BNLT] ... board_rev=[00C0] ... Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 Card did not respond to voltage select! Card did not respond to voltage select! switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 switch to partitions #0, OK mmc1(part 0) is current device gpio: pin 54 (gpio 54) value is 1 Checking for: /uEnv.txt ... Checking for: /boot.scr ... Checking for: /boot/boot.scr ... Checking for: /boot/uEnv.txt ... gpio: pin 55 (gpio 55) value is 1 2041 bytes read in 7 ms (284.2 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... gpio: pin 56 (gpio 56) value is 1 Running uname_boot ... loading /boot/vmlinuz-4.14.71-ti-r80 ... 10416640 bytes read in 664 ms (15 MiB/s) debug: [enable_uboot_overlays=1] ... debug: [enable_uboot_cape_universal=1] ... debug: [uboot_base_dtb_univ=am335x-boneblack-uboot-univ.dtb] ... uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot-univ.dtb] ... uboot_overlays: Switching too: dtb=am335x-boneblack-uboot-univ.dtb ... loading /boot/dtbs/4.14.71-ti-r80/am335x-boneblack-uboot-univ.dtb ... 161723 bytes read in 25 ms (6.2 MiB/s) uboot_overlays: [fdt_buffer=0x60000] ... uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ... 1440 bytes read in 92 ms (14.6 KiB/s) uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo ... 5127 bytes read in 151 ms (32.2 KiB/s) uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ... 711 bytes read in 51 ms (12.7 KiB/s) uboot_overlays: loading /lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo ... 3513 bytes read in 60 ms (56.6 KiB/s) loading /boot/initrd.img-4.14.71-ti-r80 ... 4530240 bytes read in 292 ms (14.8 MiB/s) debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh] ... debug: [bootz 0x82000000 0x88080000:452040 88000000] ... ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8fbad000, end 8ffff040 ... OK reserving fdt memory region: addr=88000000 size=89000 Loading Device Tree to 8fb21000, end 8fbacfff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.71-ti-r80 (root@b2-am57xx-beagle-x15-2gb) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP PREEMPT Fri Oct 5 23:50:11 UTC 2018 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 48 MiB at 0x9c800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x458 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu @df8e7000 s41548 r8192 d23988 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 440272K/522240K available (13312K kernel code, 1169K rwdata, 4364K rodata, 1024K init, 361K bss, 32816K reserved, 49152K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0e00000 (14304 kB) [ 0.000000] .init : 0xc1400000 - 0xc1500000 (1024 kB) [ 0.000000] .data : 0xc1500000 - 0xc1624498 (1170 kB) [ 0.000000] .bss : 0xc162eb2c - 0xc1689000 ( 362 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] ftrace: allocating 42734 entries in 126 pages [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000024] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000054] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000068] OMAP clocksource: timer1 at 24000000 Hz [ 0.002125] timer_probe: no matching timers found [ 0.002470] Console: colour dummy device 80x30 [ 0.002507] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.002514] This ensures that you still see kernel messages. Please [ 0.002522] update your kernel commandline. [ 0.002555] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656) [ 0.021100] pid_max: default: 32768 minimum: 301 [ 0.021377] Security Framework initialized [ 0.021397] Yama: becoming mindful. [ 0.021439] AppArmor: AppArmor disabled by boot time parameter [ 0.021521] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.021536] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.022560] CPU: Testing write buffer coherency: ok [ 0.023082] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.037186] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.045096] Hierarchical SRCU implementation. [ 0.056221] EFI services will not be available. [ 0.061104] smp: Bringing up secondary CPUs ... [ 0.061126] smp: Brought up 1 node, 1 CPU [ 0.061138] SMP: Total of 1 processors activated (995.32 BogoMIPS). [ 0.061150] CPU: All CPU(s) started in SVC mode. [ 0.062726] devtmpfs: initialized [ 0.101365] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.101849] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.101880] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.105837] xor: measuring software checksum speed [ 0.145114] arm4regs : 1200.000 MB/sec [ 0.185073] 8regs : 1075.000 MB/sec [ 0.225072] 32regs : 988.000 MB/sec [ 0.265070] neon : 1624.000 MB/sec [ 0.265081] xor: using function: neon (1624.000 MB/sec) [ 0.265101] pinctrl core: initialized pinctrl subsystem [ 0.266340] NET: Registered protocol family 16 [ 0.269356] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.360468] omap_hwmod: debugss: _wait_target_disable failed [ 0.401214] cpuidle: using governor menu [ 0.407572] OMAP GPIO hardware version 0.1 [ 0.432981] No ATAGs? [ 0.433001] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.434596] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.434630] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.529131] raid6: neonx2 gen() 1883 MB/s [ 0.597100] raid6: neonx2 xor() 1497 MB/s [ 0.597111] raid6: using algorithm neonx2 gen() 1883 MB/s [ 0.597121] raid6: .... xor() 1497 MB/s, rmw enabled [ 0.597131] raid6: using neon recovery algorithm [ 0.604907] edma 49000000.edma: TI EDMA DMA engine driver [ 0.611760] SCSI subsystem initialized [ 0.613569] usbcore: registered new interface driver usbfs [ 0.613643] usbcore: registered new interface driver hub [ 0.613762] usbcore: registered new device driver usb [ 0.614681] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.615673] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 100 kHz [ 0.616973] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 0.617512] media: Linux media interface: v0.10 [ 0.617573] Linux video capture interface: v2.00 [ 0.617760] pps_core: LinuxPPS API ver. 1 registered [ 0.617773] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.617801] PTP clock support registered [ 0.618444] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 0.621467] Advanced Linux Sound Architecture Driver Initialized. [ 0.622192] NetLabel: Initializing [ 0.622209] NetLabel: domain hash size = 128 [ 0.622219] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.622310] NetLabel: unlabeled traffic allowed by default [ 0.625532] clocksource: Switched to clocksource timer1 [ 0.789300] VFS: Disk quotas dquot_6.6.0 [ 0.789438] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.802194] NET: Registered protocol family 2 [ 0.803132] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.803183] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.803244] TCP: Hash tables configured (established 4096 bind 4096) [ 0.803368] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.803395] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.803607] NET: Registered protocol family 1 [ 0.812574] RPC: Registered named UNIX socket transport module. [ 0.812595] RPC: Registered udp transport module. [ 0.812604] RPC: Registered tcp transport module. [ 0.812612] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.813399] Unpacking initramfs... [ 1.017599] random: fast init done [ 1.060842] Freeing initrd memory: 4428K [ 1.061439] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 1.061840] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.063924] audit: initializing netlink subsys (disabled) [ 1.065185] audit: type=2000 audit(1.064:1): state=initialized audit_enabled=0 res=1 [ 1.065332] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.071410] zbud: loaded [ 1.083176] NFS: Registering the id_resolver key type [ 1.083228] Key type id_resolver registered [ 1.083238] Key type id_legacy registered [ 1.083259] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.083621] fuse init (API version 7.26) [ 1.084218] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 1.095233] Key type asymmetric registered [ 1.095262] Asymmetric key parser 'x509' registered [ 1.095389] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.099735] io scheduler noop registered [ 1.099756] io scheduler deadline registered [ 1.100158] io scheduler cfq registered (default) [ 1.100173] io scheduler mq-deadline registered [ 1.102897] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.114750] gpio-of-helper ocp:cape-universal: ready [ 1.125641] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 1.127906] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 1.131625] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 [ 1.983326] console [ttyS0] enabled [ 1.988035] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31, base_baud = 3000000) is a 8250 [ 1.998011] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32, base_baud = 3000000) is a 8250 [ 2.007862] 481a6000.serial: ttyS3 at MMIO 0x481a6000 (irq = 33, base_baud = 3000000) is a 8250 [ 2.017798] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 34, base_baud = 3000000) is a 8250 [ 2.027589] 481aa000.serial: ttyS5 at MMIO 0x481aa000 (irq = 35, base_baud = 3000000) is a 8250 [ 2.039833] omap_rng 48310000.rng: Random Number Generator ver. 20 [ 2.047465] [drm] Initialized vgem 1.0.0 20120112 for virtual device on minor 0 [ 2.055085] usbcore: registered new interface driver udl [ 2.068156] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.075482] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.082665] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.089836] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 2.097328] eqep 48300180.eqep: ver. 1.0 [ 2.101565] eqep 48300180.eqep: count_mode:0 [ 2.105890] eqep 48300180.eqep: invert_qa:1 [ 2.110118] eqep 48300180.eqep: invert_qb:1 [ 2.114343] eqep 48300180.eqep: invert_qi:0 [ 2.118568] eqep 48300180.eqep: invert_qs:0 [ 2.122793] eqep 48300180.eqep: swap_inputs:0 [ 2.127192] eqep 48300180.eqep: QDECCTL:0x0180 [ 2.131678] eqep 48300180.eqep: QPOSINIT:0x00000000 [ 2.136609] eqep 48300180.eqep: QPOSMAX:0xffffffff [ 2.141444] eqep 48300180.eqep: QPOSCNT:0x00000000 [ 2.146283] eqep 48300180.eqep: omit_interrupt:0 [ 2.150945] eqep 48300180.eqep: QEINT:0x0800 [ 2.155256] eqep 48300180.eqep: QUPRD:0x05f5e100 [ 2.159917] eqep 48300180.eqep: QEPCTL:0x009e write [ 2.164839] eqep 48300180.eqep: QEPCTL:0x009e read [ 2.169693] eqep 48300180.eqep: irq:135, clk_rate:100000000 [ 2.175555] eqep 48302180.eqep: ver. 1.0 [ 2.179682] eqep 48302180.eqep: count_mode:0 [ 2.184015] eqep 48302180.eqep: invert_qa:1 [ 2.188245] eqep 48302180.eqep: invert_qb:1 [ 2.192471] eqep 48302180.eqep: invert_qi:0 [ 2.196696] eqep 48302180.eqep: invert_qs:0 [ 2.200922] eqep 48302180.eqep: swap_inputs:0 [ 2.205322] eqep 48302180.eqep: QDECCTL:0x0180 [ 2.209810] eqep 48302180.eqep: QPOSINIT:0x00000000 [ 2.214733] eqep 48302180.eqep: QPOSMAX:0xffffffff [ 2.219567] eqep 48302180.eqep: QPOSCNT:0x00000000 [ 2.224404] eqep 48302180.eqep: omit_interrupt:0 [ 2.229064] eqep 48302180.eqep: QEINT:0x0800 [ 2.233375] eqep 48302180.eqep: QUPRD:0x05f5e100 [ 2.238036] eqep 48302180.eqep: QEPCTL:0x009e write [ 2.242958] eqep 48302180.eqep: QEPCTL:0x009e read [ 2.247806] eqep 48302180.eqep: irq:137, clk_rate:100000000 [ 2.253653] eqep 48304180.eqep: ver. 1.0 [ 2.257748] eqep 48304180.eqep: count_mode:0 [ 2.262076] eqep 48304180.eqep: invert_qa:1 [ 2.266304] eqep 48304180.eqep: invert_qb:1 [ 2.270530] eqep 48304180.eqep: invert_qi:0 [ 2.274755] eqep 48304180.eqep: invert_qs:0 [ 2.278980] eqep 48304180.eqep: swap_inputs:0 [ 2.283378] eqep 48304180.eqep: QDECCTL:0x0180 [ 2.287865] eqep 48304180.eqep: QPOSINIT:0x00000000 [ 2.292787] eqep 48304180.eqep: QPOSMAX:0xffffffff [ 2.297623] eqep 48304180.eqep: QPOSCNT:0x00000000 [ 2.302458] eqep 48304180.eqep: omit_interrupt:0 [ 2.307118] eqep 48304180.eqep: QEINT:0x0800 [ 2.311430] eqep 48304180.eqep: QUPRD:0x05f5e100 [ 2.316090] eqep 48304180.eqep: QEPCTL:0x009e write [ 2.321011] eqep 48304180.eqep: QEPCTL:0x009e read [ 2.325859] eqep 48304180.eqep: irq:139, clk_rate:100000000 [ 2.360596] libphy: Fixed MDIO Bus: probed [ 2.365804] CAN device driver interface [ 2.370985] c_can_platform 481cc000.can: c_can_platform device registered (regs=fa1cc000, irq=42) [ 2.380951] c_can_platform 481d0000.can: c_can_platform device registered (regs=fa1d0000, irq=43) [ 2.445640] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 2.453394] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.460646] MDIO: davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe] [ 2.482323] libphy: 4a101000.mdio: probed [ 2.486686] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.497153] cpsw 4a100000.ethernet: Detected MACID = 3c:e4:b0:2b:7c:c6 [ 2.504021] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 [ 2.510496] cpsw 4a100000.ethernet: ALE Table size 1024 [ 2.515834] cpsw 4a100000.ethernet: cpts: overflow check period 1250 (jiffies) [ 2.526680] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.533360] ehci-platform: EHCI generic platform driver [ 2.539019] ehci-omap: OMAP-EHCI Host Controller driver [ 2.545243] usbcore: registered new interface driver usb-storage [ 2.554617] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator [ 2.568073] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator [ 2.582560] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 2.587994] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 2.595779] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.602649] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.609929] usb usb1: Product: MUSB HDRC host driver [ 2.614940] usb usb1: Manufacturer: Linux 4.14.71-ti-r80 musb-hcd [ 2.621083] usb usb1: SerialNumber: musb-hdrc.1 [ 2.626580] hub 1-0:1.0: USB hub found [ 2.630554] hub 1-0:1.0: 1 port detected [ 2.646726] omap_rtc 44e3e000.rtc: registered as rtc0 [ 2.653336] i2c /dev entries driver [ 2.658199] Driver for 1-wire Dallas network protocol. [ 2.666761] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.674376] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0) [ 2.684401] cpuidle: enable-method property 'ti,am3352' found operations [ 2.692100] sdhci: Secure Digital Host Controller Interface driver [ 2.698394] sdhci: Copyright(c) Pierre Ossman [ 2.703663] omap_hsmmc 48060000.mmc: Got CD GPIO [ 2.786210] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.798045] ledtrig-cpu: registered to indicate activity on CPUs [ 2.804844] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.811035] omap-aes 53500000.aes: will run requests pump with realtime priority [ 2.821368] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 2.834621] hidraw: raw HID events driver (C) Jiri Kosina [ 2.840949] usbcore: registered new interface driver usbhid [ 2.846884] usbhid: USB HID core driver [ 2.851433] remoteproc remoteproc0: wkup_m3 is available [ 2.866950] wireguard: WireGuard 0.0.20180925 loaded. See www.wireguard.com for information. [ 2.875778] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld . All Rights Reserved. [ 2.886594] NET: Registered protocol family 10 [ 2.893752] mmc1: new high speed MMC card at address 0001 [ 2.899830] Segment Routing with IPv6 [ 2.899913] mip6: Mobile IPv6 [ 2.899930] NET: Registered protocol family 17 [ 2.899951] can: controller area network core (rev 20170425 abi 9) [ 2.900041] NET: Registered protocol family 29 [ 2.900165] Key type dns_resolver registered [ 2.900170] mpls_gso: MPLS GSO support [ 2.900406] omap_voltage_late_init: Voltage driver support not added [ 2.900885] PM: Cannot get wkup_m3_ipc handle [ 2.901081] ThumbEE CPU extension supported. [ 2.901105] Registering SWP/SWPB emulation handler [ 2.902293] registered taskstats version 1 [ 2.902417] zswap: loaded using pool lzo/zbud [ 2.908622] Btrfs loaded, crc32c=crc32c-generic [ 2.908720] ima: No TPM chip found, activating TPM-bypass! (rc=-19) [ 2.908741] ima: Allocated hash algorithm: sha256 [ 2.988795] mmcblk1: mmc1:0001 M62704 3.56 GiB [ 2.996369] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB [ 3.002988] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB [ 3.010236] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB [ 3.017736] mmcblk1: p1 [ 3.156452] tda998x 0-0070: found TDA19988 [ 3.162270] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops) [ 3.168441] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.175118] [drm] No driver support for vblank timestamp query. [ 3.181692] [drm] Cannot find any crtc or sizes [ 3.186985] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 1 [ 3.209211] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 [ 3.220674] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 3.226558] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.233648] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 3.241047] remoteproc remoteproc0: powering up wkup_m3 [ 3.249628] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168 [ 3.261302] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: no source widget found for Playback [ 3.270467] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 3.270488] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193 [ 3.284312] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: Failed to add route Playback -> direct -> TX [ 3.294713] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping ok [ 3.303765] PM: bootloader does not support rtc-only! [ 3.310291] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 3.319085] of_cfs_init [ 3.321760] of_cfs_init: OK [ 3.326044] ALSA device list: [ 3.329046] #0: TI BeagleBone Black [ 3.337483] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 3.797465] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 3.814694] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 3.825022] random: udevadm: uninitialized urandom read (16 bytes read) [ 4.190226] [drm] Cannot find any crtc or sizes Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Warning: fsck not present, so skipping root file system [ 27.766888] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. ================================================================================ Starting eMMC Flasher from microSD media Version: [1.20180412: all ssh regneration override...] ================================================================================ ================================================================================ Prepare environment for flashing Starting at Sat Jan 1 00:00:26 UTC 2000 ---------------------------------------- ==> Giving system time to stablize... 5 4 3 2 1 ==> Preparing /tmp ==> Preparing sysctl ==> sysctl: vm.min_free_kbytes=[2654] ==> sysctl: setting: [sysctl -w vm.min_free_kbytes=16384] vm.min_free_kbytes = 16384 ---------------------------------------- ==> Determining root drive ==> console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk1p1 ro rootfstype=ext4 rootwait init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh ---------------------------------------- ==> root_drive=[/dev/mmcblk1p1] ====> Root drive identified at [/dev/mmcblk1p1] ==> Boot Drive [/dev/mmcblk1p1] ==> Figuring out Source and Destination devices ====> Source identified: [/dev/mmcblk1] ====> Destination identified: [/dev/mmcblk0] ==> Figuring out machine ====> Machine is TI_AM335x_BeagleBone_Black ====> Machine is compatible with BeagleBone Black ================================================================================ 5 4 3 2 1 ======================================== Checking for Valid bbb-eeprom header ==> Valid bbb-eeprom header found [335] ======================================== ================================================================================ Checking running system ==> Copying: [/dev/mmcblk1] -> [/dev/mmcblk0] ==> lsblk: ---------------------------------------- NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk1 179:0 0 3.6G 0 disk `-mmcblk1p1 179:1 0 3.6G 0 part / mmcblk1boot0 179:8 0 2M 1 disk mmcblk1boot1 179:16 0 2M 1 disk mmcblk1rpmb 179:24 0 512K 0 disk ---------------------------------------- ==> df -h | grep rootfs: ---------------------------------------- !==> Error: [/dev/mmcblk0] does not exist writing to [/dev/mmcblk0] failed... ==> Stopping Cylon LEDs ... Traceback (last called is first): reset_leds() in /opt/scripts/tools/eMMC/functions.sh:433 write_failure() in /opt/scripts/tools/eMMC/functions.sh:451 check_running_system() in /opt/scripts/tools/eMMC/functions.sh:614 main() in /opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh:47 The command kill $CYLON_PID > /dev/null 2>&1 exited with exit code 2. ================================================================================ Tearing Down script environment ==> Unmounting /tmp blockdev: cannot open /dev/mmcblk0: No such file or directory ==> Stopping Cylon LEDs ... ==> Setting LEDs to [ 39.234045] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100 [ 39.234045] [ 39.243251] CPU: 0 PID: 1 Comm: init-eMMC-flash Not tainted 4.14.71-ti-r80 #1 [ 39.250419] Hardware name: Generic AM33XX (Flattened Device Tree) [ 39.256589] [] (unwind_backtrace) from [] (show_stack+0x20/0x24) [ 39.264378] [] (show_stack) from [] (dump_stack+0x80/0x94) [ 39.271653] [] (dump_stack) from [] (panic+0x100/0x284) [ 39.278656] [] (panic) from [] (complete_and_exit+0x0/0x2c) [ 39.286002] [] (complete_and_exit) from [] (do_group_exit+0x50/0xd0) [ 39.294134] [] (do_group_exit) from [] (__wake_up_parent+0x0/0x30) [ 39.302097] [] (__wake_up_parent) from [] (ret_fast_syscall+0x0/0x54) [ 39.310335] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100 [ 39.310335] [ 50.497561] random: crng init done [ 50.500983] random: 7 urandom warning(s) missed due to ratelimiting