EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 172K Warning: unable to open an initial console. init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' init: untracked pid 776 exited init: untracked pid 775 exited request_suspend_state: wakeup (3->0) at 17487702112 (1970-01-01 00:00:17.4877021 12 UTC) enabling adb adb_open init: untracked pid 800 exited init: untracked pid 803 exited init: untracked pid 802 exited init: untracked pid 808 exited init: untracked pid 807 exited init: untracked pid 829 exited init: untracked pid 828 exited init: critical process 'servicemanager' exited 4 times in 4 minutes; rebooting i nto recovery mode Restarting system with command 'recovery'. U-Boot 2010.06-rc1-00049-ga306f53 (Oct 23 2010 - 17:43:17) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 0 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Beagle unknown 0x02 Die ID #102600029ff80000016842c81202d009 Hit any key to stop autoboot: 0 mmc1 is available reading boot.scr 414 bytes read Running bootscript from mmc ... ## Executing script at 82000000 reading uImage 2452580 bytes read ***** Kernel: /dev/mmcblk0p1/uImage ***** ***** RootFS: /dev/mmcblk0p2 ***** ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-2.6.32 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2452516 Bytes = 2.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux............................................................. ................................................................................ ............. done, booting the kernel. Linux version 2.6.32 (a0393957@swubn01) (gcc version 4.4.0 (GCC) ) #1 Sat Oct 23 16:56:25 IST 2010 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 Beagle Board Memory policy: ECC disabled, Data cache writeback OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_clk ) SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 Reserving 4194304 bytes SDRAM for VRAM Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS2,115200n8 androidboot.console=ttyS2 mem=256M r oot=/dev/mmcblk0p2 rw rootfstype=ext3 rootdelay=1 init=/init ip=off mpurate=1000 omap_vout.vid1_static_vrfb_alloc=y PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 250240KB available (4240K code, 818K data, 172K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:402 Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz Reprogramming SDRC clock to 332000000 Hz GPMC revision 5.0 IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP GPIO hardware version 2.5 OMAP clockevent source: GPTIMER12 at 32768 Hz Console: colour dummy device 80x30 Calibrating delay loop... 508.37 BogoMIPS (lpj=1986560) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok regulator: core version 0.5 NET: Registered protocol family 16 Found NAND on CS0 Registering NAND on CS0 Unable to get DVI reset GPIO Target VDD1 OPP = 4, VDD2 OPP = 2 OMAP DMA hardware revision 5.0 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 regulator: VUSB1V5: 1500 mV normal standby regulator: VUSB1V8: 1800 mV normal standby regulator: VUSB3V1: 3100 mV normal standby twl4030_usb twl4030_usb: Initialized TWL4030 USB module regulator: VMMC1: 1850 <--> 3150 mV normal standby regulator: VDAC: 1800 mV normal standby regulator: VPLL2: 1800 mV normal standby regulator: VSIM: 1800 <--> 3000 mV normal standby i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz Switching to clocksource 32k_counter musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. omap-iommu omap-iommu.0: isp registered NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 489 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 console [ttyS2] enabled brd: module loaded loop: module loaded usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver dm9601 usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver gl620a usbcore: registered new interface driver net1080 usbcore: registered new interface driver plusb usbcore: registered new interface driver rndis_host usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver MOSCHIP usb-ethernet driver ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. android init android_probe pdata: c048547c android_bind android_usb gadget: android_usb ready musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected f_adb init android_register_function adb adb_bind_config f_mass_storage init android_register_function usb_mass_storage mice: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys/input/input0 i2c /dev entries driver Linux video capture interface: v2.00 omap-iommu omap-iommu.0: isp: version 1.1 OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' Advanced Linux Sound Architecture Driver Version 1.0.21. usbcore: registered new interface driver snd-usb-audio No device for DAI omap-mcbsp-dai-0 No device for DAI omap-mcbsp-dai-1 No device for DAI omap-mcbsp-dai-2 No device for DAI omap-mcbsp-dai-3 No device for DAI omap-mcbsp-dai-4 OMAP3 Beagle SoC init asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok ALSA device list: #0: omap3beagle (twl4030) TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 Power Management for TI OMAP3. Unable to set L3 frequency (400000000) Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/1000 MHz IVA2 clocking rate: 800 MHz SmartReflex driver initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 24000 kH z regulator_init_complete: incomplete constraints, leaving VDVI on regulator_init_complete: incomplete constraints, leaving VDAC on drivers/rtc/hctosys.c: unable to open rtc device (rtc0) omapdss DPI error: display already enabled omap_vout omap_vout: 'dvi' Display already enabled omapdss DPI error: display already enabled omap_vout omap_vout: 'dvi' Display already enabled omap_vout omap_vout: Buffer Size = 3686400 omap_vout omap_vout: : registered and initialized video device 0 omap_vout omap_vout: Buffer Size = 3686400 omap_vout omap_vout: : registered and initialized video device 1 Waiting 1sec before mounting root device... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address b368 mmcblk0: mmc0:b368 00000 3.74 GiB mmcblk0: p1 p2 kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is rec ommended EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): 1 truncate cleaned up EXT3-fs (mmcblk0p2): recovery complete EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 172K Warning: unable to open an initial console. init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' init: untracked pid 776 exited init: untracked pid 775 exited request_suspend_state: wakeup (3->0) at 18183342946 (1970-01-01 00:00:18.1833429 46 UTC) enabling adb adb_open init: untracked pid 800 exited init: untracked pid 803 exited init: untracked pid 802 exited init: untracked pid 816 exited init: untracked pid 815 exited init: untracked pid 836 exited init: untracked pid 835 exited init: critical process 'servicemanager' exited 4 times in 4 minutes; rebooting i nto recovery mode Restarting system with command 'recovery'. U-Boot 2010.06-rc1-00049-ga306f53 (Oct 23 2010 - 17:43:17) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 0 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Beagle unknown 0x02 Die ID #102600029ff80000016842c81202d009 Hit any key to stop autoboot: 0 mmc1 is available reading boot.scr 414 bytes read Running bootscript from mmc ... ## Executing script at 82000000 reading uImage 2452580 bytes read ***** Kernel: /dev/mmcblk0p1/uImage ***** ***** RootFS: /dev/mmcblk0p2 ***** ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-2.6.32 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2452516 Bytes = 2.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux............................................................. ................................................................................ ............. done, booting the kernel. Linux version 2.6.32 (a0393957@swubn01) (gcc version 4.4.0 (GCC) ) #1 Sat Oct 23 16:56:25 IST 2010 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 Beagle Board Memory policy: ECC disabled, Data cache writeback OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_clk ) SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 Reserving 4194304 bytes SDRAM for VRAM Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS2,115200n8 androidboot.console=ttyS2 mem=256M r oot=/dev/mmcblk0p2 rw rootfstype=ext3 rootdelay=1 init=/init ip=off mpurate=1000 omap_vout.vid1_static_vrfb_alloc=y PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 250240KB available (4240K code, 818K data, 172K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:402 Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz Reprogramming SDRC clock to 332000000 Hz GPMC revision 5.0 IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP GPIO hardware version 2.5 OMAP clockevent source: GPTIMER12 at 32768 Hz Console: colour dummy device 80x30 Calibrating delay loop... 508.37 BogoMIPS (lpj=1986560) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok regulator: core version 0.5 NET: Registered protocol family 16 Found NAND on CS0 Registering NAND on CS0 Unable to get DVI reset GPIO Target VDD1 OPP = 4, VDD2 OPP = 2 OMAP DMA hardware revision 5.0 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 regulator: VUSB1V5: 1500 mV normal standby regulator: VUSB1V8: 1800 mV normal standby regulator: VUSB3V1: 3100 mV normal standby twl4030_usb twl4030_usb: Initialized TWL4030 USB module regulator: VMMC1: 1850 <--> 3150 mV normal standby regulator: VDAC: 1800 mV normal standby regulator: VPLL2: 1800 mV normal standby regulator: VSIM: 1800 <--> 3000 mV normal standby i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz Switching to clocksource 32k_counter musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. omap-iommu omap-iommu.0: isp registered NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 489 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 console [ttyS2] enabled brd: module loaded loop: module loaded usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver dm9601 usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver gl620a usbcore: registered new interface driver net1080 usbcore: registered new interface driver plusb usbcore: registered new interface driver rndis_host usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver MOSCHIP usb-ethernet driver ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. android init android_probe pdata: c048547c android_bind android_usb gadget: android_usb ready musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected f_adb init android_register_function adb adb_bind_config f_mass_storage init android_register_function usb_mass_storage mice: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys/input/input0 i2c /dev entries driver Linux video capture interface: v2.00 omap-iommu omap-iommu.0: isp: version 1.1 OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' Advanced Linux Sound Architecture Driver Version 1.0.21. usbcore: registered new interface driver snd-usb-audio No device for DAI omap-mcbsp-dai-0 No device for DAI omap-mcbsp-dai-1 No device for DAI omap-mcbsp-dai-2 No device for DAI omap-mcbsp-dai-3 No device for DAI omap-mcbsp-dai-4 OMAP3 Beagle SoC init asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok ALSA device list: #0: omap3beagle (twl4030) TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 Power Management for TI OMAP3. Unable to set L3 frequency (400000000) Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/1000 MHz IVA2 clocking rate: 800 MHz SmartReflex driver initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 24000 kH z regulator_init_complete: incomplete constraints, leaving VDVI on regulator_init_complete: incomplete constraints, leaving VDAC on drivers/rtc/hctosys.c: unable to open rtc device (rtc0) omapdss DPI error: display already enabled omap_vout omap_vout: 'dvi' Display already enabled omapdss DPI error: display already enabled omap_vout omap_vout: 'dvi' Display already enabled omap_vout omap_vout: Buffer Size = 3686400 omap_vout omap_vout: : registered and initialized video device 0 omap_vout omap_vout: Buffer Size = 3686400 omap_vout omap_vout: : registered and initialized video device 1 Waiting 1sec before mounting root device... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address b368 mmcblk0: mmc0:b368 00000 3.74 GiB mmcblk0: p1 p2 kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is rec ommended EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): 1 truncate cleaned up EXT3-fs (mmcblk0p2): recovery complete EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 172K Warning: unable to open an initial console. init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' init: untracked pid 776 exited init: untracked pid 775 exited request_suspend_state: wakeup (3->0) at 17723225424 (1970-01-01 00:00:17.7231949 03 UTC) enabling adb adb_open init: untracked pid 799 exited init: untracked pid 803 exited init: untracked pid 802 exited init: untracked pid 808 exited init: untracked pid 807 exited request_suspend_state: wakeup (0->0) at 39804132839 (1970-01-01 00:00:39.8041023 20 UTC) init: untracked pid 834 exited init: untracked pid 851 exited init: untracked pid 850 exited request_suspend_state: wakeup (0->0) at 54273479584 (1970-01-01 00:00:54.2734490 65 UTC) init: critical process 'servicemanager' exited 4 times in 4 minutes; rebooting i nto recovery mode