U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC Phy not found PHY reset timed out cpsw, usb_ether Hit any key to stop autoboot: 1  0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 370 bytes read in 3 ms (120.1 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... Running uenvcmd ... 4002080 bytes read in 710 ms (5.4 MiB/s) 23334 bytes read in 24 ms (949.2 KiB/s) ## Booting kernel from Legacy Image at 82000000 ... Image Name: Angstrom/3.8.10/beaglebone Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4002016 Bytes = 3.8 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Deviɕblob at 88000000 Booting using the fdt blob at 0x88000000 Loading Kernel Image ... OK OK Using Device Tree in place at 88000000, end 88008b25 Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.10 (ubuntu@ip-10-195-70-130) (gcc version 4.7.3 20130205 (prerelease) (Linaro GCC 4.7-2013.02-01) ) #1 SMP Mon Apr 29 19:52:49 UTC 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0a80000 s9408 r8192 d15168 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 511MB = 511MB total [ 0.000000] Memory: 511020k/511020k available, 13268k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc057871c (5570 kB) [ 0.000000] .init : 0xc0579000 - 0xc05ab4c0 ( 202 kB) [ 0.000000] .data : 0xc05ac000 - 0xc06186a0 ( 434 kB) [ 0.000000] .bss : 0xc06186a0 - 0xc06703fc ( 352 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000363] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968) [ 0.015426] pid_max: default: 32768 minimum: 301 [ 0.015661] Security Framework initialized [ 0.015756] Mount-cache hash table entries: 512 [ 0.025524] Initializing cgroup subsys cpuacct [ 0.025557] Initializing cgroup subsys memory [ 0.025619] Initializing cgroup subsys blkio [ 0.025761] CPU: Testing write buffer coherency: ok [ 0.026298] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.026374] Setting up static identity map for 0x80340a38 - 0x80340a84 [ 0.027769] Brought up 1 CPUs [ 0.027794] SMP: Total of 1 processors activated (545.07 BogoMIPS). [ 0.028987] devtmpfs: initialized [ 0.093444] pinctrl core: initialized pinctrl subsystem [ 0.093696] rstctl core: initialized rstctl subsystem [ 0.094120] regulator-dummy: no parameters [ 0.094621] NET: Registered protocol family 16 [ 0.095325] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.105049] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105848] platform 49000000.edma: alias fck already exists [ 0.105879] platform 49000000.edma: alias fck already exists [ 0.105906] platform 49000000.edma: alias fck already exists [ 0.107235] OMAP GPIO hardware version 0.1 [ 0.111817] gpio-rctrl rstctl.3: loaded OK [ 0.117214] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.119512] cpsw.0: No hwaddr in dt. Using 50:65:83:e0:6e:a3 from efuse [ 0.119545] cpsw.1: No hwaddr in dt. Using 50:65:83:e0:6e:a5 from efuse [ 0.130445] bio: create slab at 0 [ 0.142154] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.142661] vmmcsd_fixed: 3300 mV [ 0.145426] SCSI subsystem initialized [ 0.145894] usbcore: registered new interface driver usbfs [ 0.146010] usbcore: registered new interface driver hub [ 0.146337] usbcore: registered new device driver usb [ 0.148412] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 0.150629] DCDC1: at 1500 mV [ 0.151769] vdd_mpu: 925 <--> 1325 mV at 1100 mV [ 0.152913] vdd_core: 925 <--> 1150 mV at 1100 mV [ 0.153996] LDO1: at 1800 mV [ 0.155148] LDO2: at 3300 mV [ 0.157065] LDO3: 1800 mV [ 0.158212] LDO4: at 3300 mV [ 0.159219] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 0.159898] omap_i2c 44e0b000.i2c: unable to select pin group [ 0.160660] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz [ 0.163025] omap_i2c 4819c000.i2c: unable to select pin group [ 0.163826] Advanced Linux Sound Architecture Driver Initialized. [ 0.165072] Switching to clocksource gp_timer [ 0.183069] NET: Registered protocol family 2 [ 0.184058] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.184200] TCP bind hash table entries: 4096 (order: 4, 81920 bytes) [ 0.184364] TCP: Hash tables configured (established 4096 bind 4096) [ 0.184460] TCP: reno registered [ 0.184488] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.184535] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.185027] NET: Registered protocol family 1 [ 0.185609] RPC: Registered named UNIX socket transport module. [ 0.185630] RPC: Registered udp transport module. [ 0.185644] RPC: Registered tcp transport module. [ 0.185657] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.186544] CPU PMU: probing PMU on CPU 0 [ 0.186573] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.187154] omap2_mbox_probe: platform not supported [ 0.191018] VFS: Disk quotas dquot_6.5.2 [ 0.191251] Dquot-cache hash table ent3Bzɕ0, 4096 bytes) [ 0.192438] NFS: Registering the id_resolver key type [ 0.192631] Key type id_resolver registered [ 0.192649] Key type id_legacy registered [ 0.192727] jffs2: version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc. [ 0.193156] msgmni has been set to 998 [ 0.195998] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.196023] io scheduler noop registered [ 0.196039] io scheduler deadline registered [ 0.196079] io scheduler cfq registered (default) [ 0.197720] tps65217-bl tps65217-bl: no platform data provided [ 0.197762] tps65217-bl: probe of tps65217-bl failed with error -22 [ 0.198710] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.201231] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 0.201505] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 0.872509] console [ttyO0] enabled [ 0.877176] [drm] Initialized drm 1.1.0 20060810 [ 0.895531] brd: module loaded [ 0.905823] loop: module loaded [ 0.909264] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 0.916546] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 0.923815] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 0.931081] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 0.938348] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 0.952329] bone-capemgr bone_capemgr.9: Baseboard: 'A335BNLT,BLA2,1736EL000230' [ 0.960112] bone-capemgr bone_capemgr.9: compatible-baseboard=ti,beaglebone-black [ 0.999172] bone-capemgr bone_capemgr.9: slot #0: No cape found [ 1.036285] bone-capemgr bone_capemgr.9: slot #1: No cape found [ 1.073389] bone-capemgr bone_capemgr.9: slot #2: No cape found [ 1.110498] bone-capemgr bone_capemgr.9: slot #3: No cape found [ 1.116728] bone-capemgr bone_capemgr.9: slot #4: specific override [ 1.123324] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 4 [ 1.131355] bone-capemgr bone_capemgr.9: slot #4: 'BB-BONE-RST2,00A0,Texas Instrument,BB-BONE-RST2' [ 1.140965] bone-capemgr bone_capemgr.9: slot #5: specific override [ 1.147583] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 5 [ 1.155612] bone-capemgr bone_capemgr.9: slot #5: 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G' [ 1.165761] bone-capemgr bone_capemgr.9: slot #6: specific override [ 1.172356] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 6 [ 1.180385] bone-capemgr bone_capemgr.9: slot #6: 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI' [ 1.190798] bone-capemgr bone_capemgr.9: loader: before slot-4 BB-BONE-RST2:00A0 (prio 0) [ 1.199388] bone-capemgr bone_capemgr.9: loader: check slot-4 BB-BONE-RST2:00A0 (prio 0) [ 1.207981] bone-capemgr bone_capemgr.9: loader: before slot-5 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.216832] bone-capemgr bone_capemgr.9: loader: check slot-5 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.225616] bone-capemgr bone_capemgr.9: initialized OK. [ 1.231212] bone-capemgr bone_capemgr.9: loader: before slot-6 BB-BONELT-HDMI:00A0 (prio 1) [ 1.239964] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMI:00A0 (prio 1) [ 1.250603] OneNAND driver initializing [ 1.256216] usbcore: registered new interface driver asix [ 1.261935] bone-capemgr bone_capemgr.9: loader: after slot-4 BB-BONE-RST2:00A0 (prio 0) [ 1.270516] usbcore: registered new interface driver cdc_ether [ 1.276667] bone-capemgr bone_capemgr.9: loader: check slot-5 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.285434] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMI:00A0 (prio 1) [ 1.294205] usbcore: registered new interface driver smsc95xx [ 1.300262] bone-capemgr bone_capemgr.9: slot #4: Requesting part number/version based 'BB-BONE-RST2-00A0.dtbo [ 1.310836] usbcore: registered new interface driver net1080 [ 1.316801] bone-capemgr bone_capemgr.9: slot #4: Requesting firmware 'BB-BONE-RST2-00A0.dtbo' for board-name 'BB-BONE-RST2', version '00A0' [ 1.330065] usbcore: registered new interface driver cdc_subset [ 1.336355] usbcore: registered new interface driver zaurus [ 1.342275] bone-capemgr bone_capemgr.9: slot #4: dtbo 'BB-BONE-RST2-00A0.dtbo' loaded; converting to live tree [ 1.352960] usbcore: registered new interface driver cdc_ncm [ 1.359581] Initializing USB Mass Storage driver... [ 1.364914] bone-capemgr bone_capemgr.9: slot #4: #1 overlays [ 1.371096] usbcore: registered new interface driver usb-storage [ 1.377402] USB Mass Storage support registered. [ 1.382915] test-consumer-rctrl emmc_reset_consumer.11: Trying to get NULL (OF case only) [ 1.391742] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.398078] gpio-rctrl rstctl.3: gpio_rctrl_request eMMC_RSTn [ 1.404474] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 1.409715] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:462 dsps_musb_init: OK [ 1.418560] test-consumer-rctrl emmc_reset_consumer.11: Got it (gpio:#0 name eMMC_RSTn) label:eMMC_RSTn-CONSUMER [ 1.429220] gpio-rctrl rstctl.3: gpio_rctrl_assert eMMC_RSTn [ 1.435162] test-consumer-rctrl emmc_reset_consumer.11: loaded OK [ 1.441779] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 1.446823] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 1.452812] bone-capemgr bone_capemgr.9: slot #4: Applied #1 overlays. [ 1.459690] bone-capemgr bone_capemgr.9: loader: done slot-4 BB-BONE-RST2:00A0 (prio 0) [ 1.468116] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMI:00A0 (prio 1) [ 1.476792] bone-capemgr bone_capemgr.9: loader: check slot-5 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.485650] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 1.490879] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:462 dsps_musb_init: OK [ 1.499644] bone-capemgr bone_capemgr.9: loader: after slot-6 BB-BONELT-HDMI:00A0 (prio 1) [ 1.508316] bone-capemgr bone_capemgr.9: loader: after slot-5 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.517267] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 1.522310] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 1.527619] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 1.533677] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware 'cape-boneblack-hdmi-00A0.dtbo' for board-name 'Bone-Black-HDMI', version '00A0' [ 1.547917] bone-capemgr bone_capemgr.9: slot #6: dtbo 'cape-boneblack-hdmi-00A0.dtbo' loaded; converting to live tree [ 1.559227] bone-capemgr bone_capemgr.9: slot #5: Requesting firmware 'cape-bone-2g-emmc1.dtbo' for board-name 'Bone-LT-eMMC-2G', version '00A0' [ 1.573206] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 1.581679] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.588827] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.596404] usb usb1: Product: MUSB HDRC host driver [ 1.601619] usb usb1: Manufacturer: Linux 3.8.10 musb-hcd [ 1.607290] usb usb1: SerialNumber: musb-hdrc.1.auto [ 1.612936] bone-capemgr bone_capemgr.9: slot #6: #4 overlays [ 1.619012] bone-capemgr bone_capemgr.9: slot #5: dtbo 'cape-bone-2g-emmc1.dtbo' loaded; converting to live tree [ 1.631719] platform 4830e000.fb: alias fck already exists [ 1.638721] hub 1-0:1.0: USB hub found [ 1.642719] hub 1-0:1.0: 1 port detected [ 1.647089] bone-capemgr bone_capemgr.9: slot #5: #2 overlays [ 1.654764] bone-capemgr bone_capemgr.9: slot #6: Applied #4 overlays. [ 1.661652] bone-capemgr bone_capemgr.9: loader: done slot-6 BB-BONELT-HDMI:00A0 (prio 1) [ 1.671694] mousedev: PS/2 mouse device common for all mice [ 1.677869] bone-capemgr bone_capemgr.9: slot #5: Applied #2 overlays. [ 1.684733] bone-capemgr bone_capemgr.9: loader: done slot-5 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.695698] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 1.703619] i2c /dev entries driver [ 1.708460] Driver for 1-wire Dallas network protocol. [ 1.715468] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.723095] cpuidle: using governor ladder [ 1.727455] cpuidle: using governor menu [ 1.732047] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 1.739266] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 1.745687] omap_hsmmc mmc.4: unable to select pin group [ 1.751526] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 1.758732] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 1.766065] mmc.4 supply vmmc_aux not found, using dummy regulator [ 1.773078] omap_hsmmc mmc.4: pins are not configured from the driver [ 1.806039] omap_hsmmc mmc.5: Reset gpio:0 already requested [ 1.812042] omap_hsmmc mmc.5: rstctl_request_line failed [ 1.817618] omap_hsmmc mmc.5: Unrecoverable rstctl error [ 1.823234] omap_hsmmc: probe of mmc.5 failed with error -17 [ 1.829665] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8 [ 1.841331] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22 [ 1.848634] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single [ 1.857617] leds-gpio gpio-leds.8: pins are not configured from the driver [ 1.866015] ledtrig-cpu: registered to indicate activity on CPUs [ 1.872794] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 1.880069] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 1.888568] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 1.894898] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 1.902125] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 1.910274] usbcore: registered new interface driver usbhid [ 1.916177] usbhid: USB HID core driver [ 1.923943] davinci_evm sound.14: nxp-hdmi-hifi <-> 48038000.mcasp mapping ok [ 1.935417] TCP: cubic registered [ 1.938944] Initializing XFRM netlink socket [ 1.943461] NET: Registered protocol family 17 [ 1.948236] NET: Registered protocol family 15 [ 1.953086] Key type dns_resolver registered [ 1.957729] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.965858] ThumbEE CPU extension supported. [ 1.970415] Registering SWP/SWPB emulation handler [ 1.976505] registered taskstats version 1 [ 1.984323] tilcdc 4830e000.fb: No power control GPIO [ 1.989729] mmc0: host does not support reading read-only switch. assuming write-enable. [ 1.999538] dummy 0-0034: Error -121 writing to cec:0xff [ 2.005348] tda998x 0-0070: Error -121 reading from 0xa [ 2.010991] mmc0: new high speed SDHC card at address 59b4 [ 2.016880] tda998x 0-0070: Error -121 writing to 0xa [ 2.022988] mmcblk0: mmc0:59b4 USD00 14.7 GiB [ 2.030893] mmcblk0: p1 p2 [ 2.073476] tda998x 0-0070: Error -121 reading from 0xa [ 2.079043] tda998x 0-0070: Error -121 writing to 0xa [ 2.136013] tda998x 0-0070: Error -121 reading from 0x1 [ 2.141581] tda998x 0-0070: Error -121 writing to 0x1 [ 2.146962] tda998x 0-0070: Error -121 reading from 0x1 [ 2.152525] tda998x 0-0070: Error -121 writing to 0x1 [ 2.157902] tda998x 0-0070: Error -121 writing to REG_CURPAGE [ 2.164005] tda998x 0-0070: Error -121 writing to 0x200 [ 2.169565] tda998x 0-0070: Error -121 writing to 0x201 [ 2.175126] tda998x 0-0070: Error -121 writing to 0x202 [ 2.180692] tda998x 0-0070: Error -121 writing to 0x203 [ 2.186256] tda998x 0-0070: Error -121 writing to 0x204 [ 2.191816] tda998x 0-0070: Error -121 writing to 0x205 [ 2.197376] tda998x 0-0070: Error -121 writing to 0x20e [ 2.202937] tda998x 0-0070: Error -121 writing to 0x211 [ 2.208497] tda998x 0-0070: Error -121 writing to 0x207 [ 2.214064] tda998x 0-0070: Error -121 writing to 0x208 [ 2.219624] tda998x 0-0070: Error -121 writing to 0x209 [ 2.225186] tda998x 0-0070: Error -121 writing to 0x20a [ 2.230747] tda998x 0-0070: Error -121 writing to 0x206 [ 2.236306] tda998x 0-0070: Error -121 writing to REG_CURPAGE [ 2.242412] tda998x 0-0070: Error -121 reading from 0x0 [ 2.247972] tda998x 0-0070: Error -121 reading from 0x2 [ 2.253807] tilcdc 4830e000.fb: no encoders/connectors found [ 2.259758] tilcdc 4830e000.fb: failed to initialize mode setting [ 2.317552] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.323965] davinci_mdio 4a101000.mdio: no live phy, scanning all [ 2.330728] davinci_mdio: probe of 4a101000.mdio failed with error -5 [ 2.337796] Detected MACID = 50:65:83:e0:6e:a3 [ 2.342351] Unhandled fault: external abort on non-linefetch (0x1008) at 0xe09fe000 [ 2.350538] Internal error: : 1008 [#1] SMP THUMB2 [ 2.355536] Modules linked in: [ 2.358737] CPU: 0 Not tainted (3.8.10 #1) [ 2.363389] PC is at cpsw_probe+0x3fc/0x8a2 [ 2.367771] LR is at ioremap_page_range+0xc3/0x100 [ 2.372783] pc : [] lr : [] psr: 80000133 [ 2.372783] sp : df051e18 ip : df04b7f8 fp : 00000001 [ 2.384776] r10: df336620 r9 : df34e590 r8 : 00000000 [ 2.390239] r7 : e09fe000 r6 : df10ca00 r5 : df10ca10 r4 : df34e000 [ 2.397057] r3 : 00000000 r2 : 00000800 r1 : c023cc8d r0 : e09fe000 [ 2.403880] Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment kernel [ 2.411696] Control: 50c5387d Table: 80004019 DAC: 00000015 [ 2.417701] Process swapper/0 (pid: 1, stack limit = 0xdf050240) [ 2.423977] Stack: (0xdf051e18 to 0xdf052000) [ 2.428532] 1e00: 00000000 c03408cf [ 2.437083] 1e20: 00000000 c008ee03 df34e298 c033f3cb df04aac0 00000000 df051e4c 00000020 [ 2.445634] 1e40: 00000008 c00ce159 df051e90 df3b2a88 df051e78 df04aac0 df3b2bc8 df3b2a88 [ 2.454185] 1e60: df3b2a88 c00ce09b 00000000 df3b2a88 df10a388 df3b5ec0 00000000 c00ce877 [ 2.462737] 1e80: df0454b8 c0040161 00000000 00000003 df10a388 00000000 c0606080 df10ca10 [ 2.471288] 1ea0: df10ca44 c0606080 c01f0225 000000b4 c0590fc1 00000000 00000000 c01f0b91 [ 2.479839] 1ec0: c01f0b85 c01f0147 00000000 df10ca10 df10ca44 c0606080 c01f0225 c01f0259 [ 2.488388] 1ee0: 00000000 df051ef0 c0606080 c01ef275 df045478 df10bd00 c0606080 c0606080 [ 2.496943] 1f00: df3b5ec0 c05fc990 00000000 c01efc0b c04b42fe df001348 c0606080 c0598e30 [ 2.505492] 1f20: c05a82b4 c06186c0 000000b4 c01f0539 00000007 c0598e30 c05a82b4 c06186c0 [ 2.514041] 1f40: 000000b4 c000868d c0590fc1 13000000 c05a82dc 00000008 00000007 c0598e30 [ 2.522590] 1f60: c05a82b4 c06186c0 000000b4 c0598e38 c05791d5 c0579691 00000007 00000007 [ 2.531141] 1f80: c05791d5 00000000 00000000 c0338ebd 00000000 00000000 00000000 00000000 [ 2.539689] 1fa0: 00000000 c0338ec3 00000000 c000c6fd 00000000 00000000 00000000 00000000 [ 2.548240] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.556787] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff [ 2.565360] [] (cpsw_probe+0x3fc/0x8a2) from [] (platform_drv_probe+0xd/0xe) [ 2.574542] [] (platform_drv_probe+0xd/0xe) from [] (driver_probe_device+0x67/0x144) [ 2.584446] [] (driver_probe_device+0x67/0x144) from [] (__driver_attach+0x35/0x48) [ 2.594258] [] (__driver_attach+0x35/0x48) from [] (bus_for_each_dev+0x29/0x48) [ 2.603706] [] (bus_for_each_dev+0x29/0x48) from [] (bus_add_driver+0x83/0x158) [ 2.613155] [] (bus_add_driver+0x83/0x158) from [] (driver_register+0x4d/0xa4) [ 2.622516] [] (driver_register+0x4d/0xa4) from [] (do_one_initcall+0x61/0xec) [ 2.631880] [] (do_one_initcall+0x61/0xec) from [] (kernel_init_freeable+0xb9/0x14c) [ 2.641792] [] (kernel_init_freeable+0xb9/0x14c) from [] (kernel_init+0x7/0x90) [ 2.651251] [] (kernel_init+0x7/0x90) from [] (ret_from_fork+0x11/0x34) [ 2.659970] Code: fc30 e200 f8c4 05c0 (6803) f44f [ 2.664975] ---[ end trace 681ee094da821926 ]--- [ 2.669911] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 2.669911]