U-Boot SPL 2015.07-rc2-00001-g15e7184 (Jun 09 2015 - 09:01:57) U-Boot 2015.07-rc2-00001-g15e7184 (Jun 09 2015 - 09:01:57 -0500), Build: jenkins-github_Bootloader-Builder-163 Watchdog enabled I2C: ready DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Net: not set. Validating first E-fuse MAC cpsw Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 switch to partitions #0, OK mmc0 is current device gpio: pin 54 (gpio 54) value is 1 Checking for: /uEnv.txt ... 1179 bytes read in 11 ms (104.5 KiB/s) gpio: pin 55 (gpio 55) value is 1 Loaded environment from uEnv.txt Importing environment from mmc ... Checking if uenvcmd is set ... gpio: pin 56 (gpio 56) value is 1 Running uenvcmd ... 538 bytes read in 63 ms (7.8 KiB/s) debug: [/boot/vmlinuz-3.14.43-ti-r67] ... 7131184 bytes read in 437 ms (15.6 MiB/s) debug: [/boot/initrd.img-3.14.43-ti-r67] ... 3634409 bytes read in 239 ms (14.5 MiB/s) debug: [/boot/dtbs/3.14.43-ti-r67/am335x-boneblack.dtb] ... 87161 bytes read in 151 ms (563.5 KiB/s) debug: [console=tty0 console=ttyO0,115200n8 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait fixrtc init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh] ... debug: [bootz 0x82000000 0x88080000:3774e9 0x88000000] ... Kernel image @ 0x82000000 [ 0x000000 - 0x6cd030 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 88018478 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.14.43-ti-r67 (root@a4-imx6q-wandboard-2gb) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-19ubuntu1) ) #1 SMP PREEMPT Thu Jun 4 19:06:02 UTC 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone Black [ 0.000000] cma: CMA: reserved 24 MiB at 9e000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @df9b5000 s14208 r8192 d14464 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536 [ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait fixrtc init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 473880K/522240K available (8995K kernel code, 701K rwdata, 3264K rodata, 601K init, 744K bss, 48360K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0c0100c (12261 kB) [ 0.000000] .init : 0xc0c02000 - 0xc0c98780 ( 602 kB) [ 0.000000] .data : 0xc0c9a000 - 0xc0d49774 ( 702 kB) [ 0.000000] .bss : 0xc0d49774 - 0xc0e03a68 ( 745 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000036] OMAP clocksource: timer1 at 24000000 Hz [ 0.000389] Console: colour dummy device 80x30 [ 0.001418] console [tty0] enabled [ 0.001455] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.001486] This ensures that you still see kernel messages. Please [ 0.001514] update your kernel commandline. [ 0.001554] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) [ 0.088475] pid_max: default: 32768 minimum: 301 [ 0.088643] Security Framework initialized [ 0.088744] AppArmor: AppArmor disabled by boot time parameter [ 0.088779] Yama: becoming mindful. [ 0.088885] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.088924] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.131930] Initializing cgroup subsys memory [ 0.132035] Initializing cgroup subsys devices [ 0.132065] Initializing cgroup subsys freezer [ 0.132094] Initializing cgroup subsys net_cls [ 0.132120] Initializing cgroup subsys blkio [ 0.132146] Initializing cgroup subsys perf_event [ 0.132178] Initializing cgroup subsys net_prio [ 0.132319] CPU: Testing write buffer coherency: ok [ 0.132405] ftrace: allocating 31444 entries in 93 pages [ 0.220754] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.220865] Setting up static identity map for 0x808ceac8 - 0x808ceb20 [ 0.278514] Brought up 1 CPUs [ 0.278570] SMP: Total of 1 processors activated (996.14 BogoMIPS). [ 0.278592] CPU: All CPU(s) started in SVC mode. [ 0.279564] devtmpfs: initialized [ 0.283912] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.300745] omap_hwmod: tptc0 using broken dt data from edma [ 0.300966] omap_hwmod: tptc1 using broken dt data from edma [ 0.301135] omap_hwmod: tptc2 using broken dt data from edma [ 0.306166] omap_hwmod: debugss: _wait_target_disable failed [ 0.367153] xor: measuring software checksum speed [ 0.458480] arm4regs : 1244.000 MB/sec [ 0.558471] 8regs : 1073.200 MB/sec [ 0.658471] 32regs : 1036.000 MB/sec [ 0.758470] neon : 1720.400 MB/sec [ 0.758490] xor: using function: neon (1720.400 MB/sec) [ 0.758525] pinctrl core: initialized pinctrl subsystem [ 0.759101] regulator-dummy: no parameters [ 0.760955] NET: Registered protocol family 16 [ 0.763296] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.763989] cpuidle: using governor ladder [ 0.764019] cpuidle: using governor menu [ 0.769235] syscon 44e10000.control_module: regmap [mem 0x44e10000-0x44e107fb] registered [ 0.770166] syscon 44e10000.syscon: regmap [mem 0x44e10000-0x44e107ff] registered [ 0.770802] platform 49000000.edma: alias fck already exists [ 0.770843] platform 49000000.edma: alias fck already exists [ 0.770869] platform 49000000.edma: alias fck already exists [ 0.771813] OMAP GPIO hardware version 0.1 [ 0.795551] No ATAGs? [ 0.795594] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.806517] bio: create slab at 0 [ 0.968581] raid6: int32x1 212 MB/s [ 1.138619] raid6: int32x2 291 MB/s [ 1.308632] raid6: int32x4 305 MB/s [ 1.478531] raid6: int32x8 288 MB/s [ 1.648488] raid6: neonx1 1446 MB/s [ 1.818489] raid6: neonx2 1860 MB/s [ 1.988473] raid6: neonx4 1943 MB/s [ 2.158507] raid6: neonx8 734 MB/s [ 2.158526] raid6: using algorithm neonx4 (1943 MB/s) [ 2.158545] raid6: using intx1 recovery algorithm [ 2.168994] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 2.170009] vbat: 5000 mV [ 2.170356] vmmcsd_fixed: 3300 mV [ 2.173708] i2c-core: driver [palmas] using legacy suspend method [ 2.173742] i2c-core: driver [palmas] using legacy resume method [ 2.174148] SCSI subsystem initialized [ 2.174903] usbcore: registered new interface driver usbfs [ 2.174999] usbcore: registered new interface driver hub [ 2.175206] usbcore: registered new device driver usb [ 2.175812] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 2.175868] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 2.179213] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 2.179713] pps_core: LinuxPPS API ver. 1 registered [ 2.179741] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.179788] PTP clock support registered [ 2.180904] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 2.182295] Advanced Linux Sound Architecture Driver Initialized. [ 2.183292] Switched to clocksource timer1 [ 2.278169] NET: Registered protocol family 2 [ 2.279307] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 2.279382] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 2.279457] TCP: Hash tables configured (established 4096 bind 4096) [ 2.279542] TCP: reno registered [ 2.279567] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.279602] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.279890] NET: Registered protocol family 1 [ 2.280430] RPC: Registered named UNIX socket transport module. [ 2.280464] RPC: Registered udp transport module. [ 2.280482] RPC: Registered tcp transport module. [ 2.280499] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.281258] Unpacking initramfs... [ 2.524622] Freeing initrd memory: 3548K (c8080000 - c83f7000) [ 2.525017] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 2.528194] futex hash table entries: 256 (order: 2, 16384 bytes) [ 2.528433] audit: initializing netlink subsys (disabled) [ 2.528527] audit: type=2000 audit(2.470:1): initialized [ 2.638809] zbud: loaded [ 2.639246] VFS: Disk quotas dquot_6.5.2 [ 2.639399] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.640212] NFS: Registering the id_resolver key type [ 2.640327] Key type id_resolver registered [ 2.640347] Key type id_legacy registered [ 2.640377] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.640749] fuse init (API version 7.22) [ 2.640998] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [ 2.641823] msgmni has been set to 980 [ 2.644210] NET: Registered protocol family 38 [ 2.644359] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 2.644617] io scheduler noop registered [ 2.644642] io scheduler deadline registered [ 2.644694] io scheduler cfq registered (default) [ 2.646639] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 2.651786] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 2.656513] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a 8250 [ 3.532602] console [ttyS0] enabled [ 3.537186] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a 8250 [ 3.546920] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a 8250 [ 3.556660] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a 8250 [ 3.566380] 481aa000.serial: ttyS5 at MMIO 0x481aa000 (irq = 62, base_baud = 3000000) is a 8250 [ 3.577762] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 3.584914] [drm] Initialized drm 1.1.0 20060810 [ 3.589770] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.596796] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.603782] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.610741] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.621309] bone-pinmux-helper ocp:P8_27_pinmux: Set initial pinmux mode to hdmi [ 3.629317] bone-pinmux-helper ocp:P8_28_pinmux: Set initial pinmux mode to hdmi [ 3.637258] bone-pinmux-helper ocp:P8_29_pinmux: Set initial pinmux mode to hdmi [ 3.645197] bone-pinmux-helper ocp:P8_30_pinmux: Set initial pinmux mode to hdmi [ 3.653052] bone-pinmux-helper ocp:P8_31_pinmux: Set initial pinmux mode to hdmi [ 3.660915] bone-pinmux-helper ocp:P8_32_pinmux: Set initial pinmux mode to hdmi [ 3.668791] bone-pinmux-helper ocp:P8_33_pinmux: Set initial pinmux mode to hdmi [ 3.676737] bone-pinmux-helper ocp:P8_34_pinmux: Set initial pinmux mode to hdmi [ 3.684645] bone-pinmux-helper ocp:P8_35_pinmux: Set initial pinmux mode to hdmi [ 3.692575] bone-pinmux-helper ocp:P8_36_pinmux: Set initial pinmux mode to hdmi [ 3.700645] bone-pinmux-helper ocp:P8_37_pinmux: Set initial pinmux mode to hdmi [ 3.708741] bone-pinmux-helper ocp:P8_38_pinmux: Set initial pinmux mode to hdmi [ 3.716866] bone-pinmux-helper ocp:P8_39_pinmux: Set initial pinmux mode to hdmi [ 3.724998] bone-pinmux-helper ocp:P8_40_pinmux: Set initial pinmux mode to hdmi [ 3.733119] bone-pinmux-helper ocp:P8_41_pinmux: Set initial pinmux mode to hdmi [ 3.741316] bone-pinmux-helper ocp:P8_42_pinmux: Set initial pinmux mode to hdmi [ 3.749610] bone-pinmux-helper ocp:P8_43_pinmux: Set initial pinmux mode to hdmi [ 3.757935] bone-pinmux-helper ocp:P8_44_pinmux: Set initial pinmux mode to hdmi [ 3.766318] bone-pinmux-helper ocp:P8_45_pinmux: Set initial pinmux mode to hdmi [ 3.774731] bone-pinmux-helper ocp:P8_46_pinmux: Set initial pinmux mode to hdmi [ 3.788166] bone-pinmux-helper ocp:P9_19_pinmux: Set initial pinmux mode to i2c [ 3.796490] bone-pinmux-helper ocp:P9_20_pinmux: Set initial pinmux mode to i2c [ 3.809166] bone-pinmux-helper ocp:P9_25_pinmux: Set initial pinmux mode to audio [ 3.820777] bone-pinmux-helper ocp:P9_28_pinmux: Set initial pinmux mode to audio [ 3.829974] bone-pinmux-helper ocp:P9_29_pinmux: Set initial pinmux mode to audio [ 3.840566] bone-pinmux-helper ocp:P9_31_pinmux: Set initial pinmux mode to audio [ 3.856938] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.863643] ehci-omap: OMAP-EHCI Host Controller driver [ 3.869272] usbcore: registered new interface driver usb-storage [ 3.877945] 47401300.usb-phy supply vcc not found, using dummy regulator [ 4.016203] musb-hdrc musb-hdrc.0.auto: Failed to request rx1. [ 4.022192] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517 [ 4.030144] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral [ 4.038750] 47401b00.usb-phy supply vcc not found, using dummy regulator [ 4.136342] musb-hdrc musb-hdrc.1.auto: Failed to request rx1. [ 4.142329] musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517 [ 4.150279] platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral [ 4.167566] mousedev: PS/2 mouse device common for all mice [ 4.174295] i2c-core: driver [rtc-ds1307] using legacy suspend method [ 4.180800] i2c-core: driver [rtc-ds1307] using legacy resume method [ 4.188526] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 4.196681] i2c /dev entries driver [ 4.202622] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 4.315907] ledtrig-cpu: registered to indicate activity on CPUs [ 4.322540] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 4.331005] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 4.338709] hidraw: raw HID events driver (C) Jiri Kosina [ 4.345561] usbcore: registered new interface driver usbhid [ 4.351228] usbhid: USB HID core driver [ 4.356019] ashmem: initialized [ 4.360505] platform 44d00000.wkup_m3: Driver wkup_m3 requests probe deferral [ 4.371946] mmc0: host does not support reading read-only switch. assuming write-enable. [ 4.383731] davinci_evm sound: hdmi-hifi <-> 48038000.mcasp mapping ok [ 4.392812] oprofile: using arm/armv7 [ 4.396852] mmc0: new high speed SD card at address aaaa [ 4.403456] TCP: cubic registered [ 4.406887] NET: Registered protocol family 10 [ 4.412069] mmcblk0: mmc0:aaaa SU02G 1.84 GiB [ 4.418143] mip6: Mobile IPv6 [ 4.421344] mmcblk0: p1 [ 4.424926] NET: Registered protocol family 17 [ 4.429661] Key type dns_resolver registered [ 4.435116] mpls_gso: MPLS GSO support [ 4.442239] cpu cpu0: of_pm_voltdm_notifier_register: Failed to get cpu0 regulator/voltdm: -517 [ 4.451210] cpu cpu0: cpu0 clock notifier not ready, retry [ 4.456888] platform cpufreq-cpu0.0: Driver cpufreq-cpu0 requests probe deferral [ 4.465466] PM: bootloader does not support rtc-only! [ 4.470659] ThumbEE CPU extension supported. [ 4.475129] Registering SWP/SWPB emulation handler [ 4.483942] registered taskstats version 1 [ 4.488437] bio: create slab at 1 [ 4.493035] Btrfs loaded [ 4.495817] vbat: disabling [ 4.498640] regulator-dummy: disabling [ 4.503156] Error: Driver 'tfp410' is already registered, aborting... [ 4.511226] slave hdmi: could not get i2c [ 4.515584] platform hdmi: Driver slave requests probe deferral [ 4.522495] platform 4830e000.lcdc: Driver tilcdc requests probe deferral [ 4.532866] mmc1: BKOPS_EN bit is not set [ 4.543972] input: tps65217_pwr_but as /devices/ocp/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 4.555358] mmc1: new high speed MMC card at address 0001 [ 4.561521] DCDC1: at 1500 mV [ 4.564998] mmcblk1: mmc1:0001 MMC02G 1.78 GiB [ 4.570389] mmcblk1boot0: mmc1:0001 MMC02G partition 1 1.00 MiB [ 4.576864] vdd_mpu: 925 <--> 1375 mV at 1325 mV [ 4.581763] mmcblk1boot1: mmc1:0001 MMC02G partition 2 1.00 MiB [ 4.588912] vdd_core: 925 <--> 1150 mV at 1125 mV [ 4.595442] mmcblk1: p1 [ 4.598359] LDO1: at 1800 mV [ 4.603345] mmcblk1boot1: unknown partition table [ 4.609424] LDO2: at 3300 mV [ 4.613499] mmcblk1boot0: unknown partition table [ 4.619313] LDO3: 1800 mV [ 4.623183] LDO4: at 3300 mV [ 4.627491] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 4.639510] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 4.646728] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 4.670603] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 4.676881] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 4.685134] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.691976] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.699324] usb usb1: Product: MUSB HDRC host driver [ 4.704354] usb usb1: Manufacturer: Linux 3.14.43-ti-r67 musb-hcd [ 4.710488] usb usb1: SerialNumber: musb-hdrc.1.auto [ 4.716699] hub 1-0:1.0: USB hub found [ 4.720555] hub 1-0:1.0: 1 port detected [ 4.778353] remoteproc0: wkup_m3 is available [ 4.782860] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 4.791958] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 4.803565] remoteproc0: powering up wkup_m3 [ 4.808045] cpu cpu0: of_pm_voltdm_notifier_register: Fail calculating voltage latency[950000<->1325000]:-22 [ 4.817988] remoteproc0: Booting fw image am335x-pm-firmware.elf, size 219827 [ 4.828793] PM: CM3 Firmware Version = 0x190 [ 4.834434] remoteproc0: remote processor wkup_m3 is now up [ 4.966340] tilcdc 4830e000.lcdc: found TDA19988 [ 4.971745] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 4.978453] [drm] No driver support for vblank timestamp query. [ 4.985052] tilcdc 4830e000.lcdc: No connectors reported connected with modes [ 4.992263] [drm] Cannot find any crtc or sizes - going 1024x768 [ 5.010614] Console: switching to colour frame buffer device 128x48 [ 5.021820] tilcdc 4830e000.lcdc: fb0: frame buffer device [ 5.027509] tilcdc 4830e000.lcdc: registered panic notifier [ 5.033200] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 5.103424] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 5.109675] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 5.123709] libphy: 4a101000.mdio: probed [ 5.127862] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 5.138651] cpsw 4a100000.ethernet: Detected MACID = d0:ff:50:07:d3:c4 [ 5.147437] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 5.161330] ALSA device list: [ 5.164523] #0: TI BeagleBone Black [ 5.169412] Freeing unused kernel memory: 600K (c0c02000 - c0c98000) Loading, please wait... [ 5.269566] systemd-udevd[117]: starting version 204 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 6.394158] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. Starting eMMC Flasher ----------------------------- Checking for Valid BBB EEPROM header Valid BBB EEPROM header found [335] ----------------------------- copying: [/dev/mmcblk0] -> [/dev/mmcblk1] lsblk: NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk1boot0 179:16 0 1M 1 disk mmcblk1boot1 179:24 0 1M 1 disk mmcblk0 179:0 0 1.9G 0 disk `-mmcblk0p1 179:1 0 1.7G 0 part / mmcblk1 179:8 0 1.8G 0 disk `-mmcblk1p1 179:9 0 1.8G 0 part ----------------------------- df -h | grep rootfs: df: '/run/lock': No such file or directory df: '/run/shm': No such file or directory df: '/run/user': No such file or directory ----------------------------- Erasing: /dev/mmcblk1 [ 7.631629] random: nonblocking pool is initialized 108+0 records in 108+0 records out 113246208 bytes (113 MB) copied, 18.001 s, 6.3 MB/s 108+0 records in 108+0 records out 113246208 bytes (113 MB) copied, 4.39997 s, 25.7 MB/s Erasing: /dev/mmcblk1 complete ----------------------------- Writing bootloader to [/dev/mmcblk1] dd if=/opt/backup/uboot/MLO of=/dev/mmcblk1 count=1 seek=1 conv=notrunc bs=128k ----------------------------- 0+1 records in 0+1 records out 75520 bytes (76 kB) copied, 0.0213253 s, 3.5 MB/s ----------------------------- dd if=/opt/backup/uboot/u-boot.img of=/dev/mmcblk1 count=2 seek=1 conv=notrunc bs=384k ----------------------------- 1+1 records in 1+1 records out 411236 bytes (411 kB) copied, 0.13248 s, 3.1 MB/s ----------------------------- Formatting: /dev/mmcblk1 Checking that no-one is using this disk right now ...[ 29.973190] mmcblk1: unknown partition table OK Disk /dev/mmcblk1: 58624 cylinders, 4 heads, 16 sectors/track sfdisk: ERROR: sector 3069612032 does not have an msdos signature /dev/mmcblk1: unrecognized partition table type Old situation: No partitions found New situation: Units = mebibytes [ 30.000300] mmcblk1: p1 of 1048576 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End MiB #blocks Id System /dev/mmcblk1p1 * 1 1831 1831 1874944 83 Linux /dev/mmcblk1p2 0 - 0 0 0 Empty /dev/mmcblk1p3 0 - 0 0 0 Empty /dev/mmcblk1p4 0 - 0 0 0 Empty Successfully wrote the new partition table Re-reading the partition table ... If you created or changed a DOS partition, /dev/foo7, say, then use dd(1) to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1 (See fdisk(8).) mkfs.ext4 /dev/mmcblk1p1 -L BOOT ----------------------------- mke2fs 1.42.9 (4-Feb-2014) Discarding device blocks: done Filesystem label=BOOT OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 117360 inodes, 468736 blocks 23436 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=482344960 15 block groups 32768 blocks per group, 32768 fragments per group 7824 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912 Allocating group tables: done Writing inode tables: done Creating journal (8192 blocks): done Writing superblocks and filesystem accounting information: done ----------------------------- Formatting: /dev/mmcblk1 complete ----------------------------- Copying: /dev/mmcblk0p1 -> /dev/mmcblk1p1 [ 39.436176] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null) rsync: / -> /tmp/rootfs/ rsync: ignore the % values when shown as they are not accurate... [ 92.187459] mmcblk1: timed out sending r/w cmd command, card status 0xe00 [ 92.196777] end_request: I/O error, dev mmcblk1, sector 723040 [ 92.205019] end_request: I/O error, dev mmcblk1, sector 723048 [ 92.215798] end_request: I/O error, dev mmcblk1, sector 723056 [ 92.227958] end_request: I/O error, dev mmcblk1, sector 723064 [ 92.236296] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4515 (offset 0 size 16384 starting block 90384) [ 92.253725] Buffer I/O error on device mmcblk1p1, logical block 90124 [ 92.262395] Buffer I/O error on device mmcblk1p1, logical block 90125 [ 92.271038] Buffer I/O error on device mmcblk1p1, logical block 90126 [ 92.279628] Buffer I/O error on device mmcblk1p1, logical block 90127 [ 92.289073] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.352885] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.366932] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.428349] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.463805] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.476275] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.489353] end_request: I/O error, dev mmcblk1, sector 723072 [ 92.497447] end_request: I/O error, dev mmcblk1, sector 723080 [ 92.505312] end_request: I/O error, dev mmcblk1, sector 723088 [ 92.513034] end_request: I/O error, dev mmcblk1, sector 723096 [ 92.520801] end_request: I/O error, dev mmcblk1, sector 723104 [ 92.528520] end_request: I/O error, dev mmcblk1, sector 723112 [ 92.536941] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4517 (offset 0 size 1249280 starting block 90512) [ 92.553897] Buffer I/O error on device mmcblk1p1, logical block 90128 [ 92.562367] Buffer I/O error on device mmcblk1p1, logical block 90129 [ 92.570833] Buffer I/O error on device mmcblk1p1, logical block 90130 [ 92.579279] Buffer I/O error on device mmcblk1p1, logical block 90131 [ 92.587701] Buffer I/O error on device mmcblk1p1, logical block 90132 [ 92.598725] Buffer I/O error on device mmcblk1p1, logical block 90133 [ 92.638133] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.673774] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.709137] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.751120] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.761107] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.796452] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.806153] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4517 (offset 0 size 1249280 starting block 90640) [ 92.877945] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.891591] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.952666] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 92.987867] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.000063] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.013802] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.023205] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4517 (offset 0 size 1249280 starting block 90689) [ 93.040249] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4519 (offset 0 size 24576 starting block 90695) [ 93.057162] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4520 (offset 0 size 73728 starting block 90713) [ 93.074368] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4521 (offset 0 size 49152 starting block 90725) [ 93.091797] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4527 (offset 0 size 102400 starting block 90750) [ 93.109443] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4556 (offset 0 size 8192 starting block 90752) [ 93.130480] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.144882] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.180967] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.191112] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.226832] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.265296] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.279210] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:317: I/O error -5 writing to inode 4518 (offset 0 size 262144 starting block 90816) [ 93.324372] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.360580] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.399308] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.413951] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.475962] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.512117] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.526385] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.566361] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.627897] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.666216] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.680363] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.741898] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.807035] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.821132] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.882706] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.918366] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.931059] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 93.945272] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.007568] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.017818] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.056208] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.070237] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.131973] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.167675] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.210947] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.221204] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.256869] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.292451] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.302251] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.314812] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.355593] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.391068] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.426140] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.438203] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.477302] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.538005] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.576936] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.590033] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.624851] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.659256] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.696334] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.709095] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.744813] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.779075] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.841597] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.854427] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.888790] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.948424] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.964686] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 94.998955] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.058611] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.099270] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.133643] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.193204] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.204810] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.268782] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.303222] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.311683] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.345666] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.382302] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.396200] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.455988] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.490007] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.501110] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.513571] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.547659] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.556641] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.618968] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.631331] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.691187] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.725227] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.736246] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.749564] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.783849] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.843537] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.854753] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.918406] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.926996] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 95.961816] mmcblk1: timed out sending r/w cmd command, card status 0x400e00 [ 96.024283] mmcblk1: timed out sending r/w cmd command, card status 0x400e00