U-Boot SPL 2021.01-gdaedcf37 (Sep 21 2022 - 23:44:04 +0000) Model: Texas Instruments K3 J721E SoC EEPROM not available at 0x50, trying to read at 0x51 Board: BBONEAI-64-B0- rev B0 SYSFW ABI: 3.1 (firmware rev 0x0015 '21.9.1--v2021.09a (Terrific Lla') TLB table from ffffc000 to 00000000 >>SPL: board_init_r() spl_init Trying to boot from MMC1 spl: mmc boot mode: fs board_fit_image_post_process: processing image: addr=70000000, size=39864, os=arm-trusted-firmware board_fit_image_post_process: matched image for ID 0 board_fit_image_post_process: processing image: addr=9e800000, size=374648, os=tee board_fit_image_post_process: matched image for ID 1 board_fit_image_post_process: processing image: addr=89000000, size=217356, os=DM board_fit_image_post_process: matched image for ID 3 board_fit_image_post_process: processing image: addr=80080000, size=163184, os=U-Boot board_fit_image_post_process: matched image for ID 2 board_fit_image_post_process: processing image: addr=ffffffff, size=10103, os= Unsupported OS image.. Jumping nevertheless.. loaded - jumping to U-Boot... init_env from device 17 not supported! jump_to_image_no_args: jumping to address 41010000 Starting ATF on ARM64 core... NOTICE: BL31: v2.5(release):0588523 NOTICE: BL31: Built : 23:44:04, Sep 21 2022 U-Boot SPL 2021.01-gdaedcf37 (Sep 21 2022 - 23:44:04 +0000) Model: Texas Instruments K3 J721E SoC Board: BBONEAI-64-B0- rev B0 SYSFW ABI: 3.1 (firmware rev 0x0015 '21.9.1--v2021.09a (Terrific Lla') TLB table from ffff4000 to 100000000 SPL malloc() before relocation used 0x2500 bytes (9 KB) >>SPL: board_init_r() spl_init ti_i2c_eeprom_am6_parse_record: Ignoring record id 17 Trying to boot from MMC1 spl: mmc boot mode: fs Jumping to U-Boot loaded - jumping to U-Boot... image entry point: 0x80800000 U-Boot 2021.01-gdaedcf37 (Sep 21 2022 - 23:44:04 +0000) SoC: J721E SR2.0 Model: Texas Instruments K3 J721E SoC Board: BBONEAI-64-B0- rev B0 DRAM: 4 GiB Flash: 0 Bytes MMC: sdhci@4f80000: 0, sdhci@4fb0000: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial@2800000 Out: serial@2800000 Err: serial@2800000 ti_i2c_eeprom_am6_parse_record: Ignoring record id 17 Net: am65_cpsw_nuss_slave ethernet@46000000: K3 CPSW: nuss_ver: 0x6BA00101 cpsw_ver: 0x6BA80100 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000 eth0: ethernet@46000000 Press SPACE to abort autoboot in 2 seconds board_name=[BBONEAI-64-B0-] ... name_fdt=[k3-j721e-beagleboneai64.dtb] ... MMC: no card present mmc_init: -123, time 2002 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 203 bytes read in 8 ms (24.4 KiB/s) 1: Linux eMMC Retrieving file: /initrd.img 15772739 bytes read in 93 ms (161.7 MiB/s) Retrieving file: /Image 28813824 bytes read in 164 ms (167.6 MiB/s) append: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait net.ifnames=0 Retrieving file: /k3-j721e-beagleboneai64.dtb 203817 bytes read in 9 ms (21.6 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8f0f5000, end 8ffffc43 ... OK Loading Device Tree to 000000008f0c0000, end 000000008f0f4c28 ... OK Linux kernel Image start = 0x82000000 end = 0x83c40000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd080] [ 0.000000] Linux version 5.10.120-ti-arm64-r63 (voodoo@rpi4b8g-19) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1bullseye SMP Fri Sep 2 01:18:17 UTC 2022 [ 0.000000] Machine model: BeagleBoard.org BeagleBone AI-64 [ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a0000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-dma-memory@a0000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a0100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-memory@a0100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a1000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-dma-memory@a1000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a1100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-memory@a1100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a2000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-dma-memory@a2000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a2100000, size 31 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-memory@a2100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a4000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-dma-memory@a4000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a4100000, size 31 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-memory@a4100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a6000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-dma-memory@a6000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a6100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-memory@a6100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a7000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-dma-memory@a7000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a7100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-memory@a7100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a8000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-c66-dma-memory@a8000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a8100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-c66-memory@a8100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a9000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-c66-dma-memory@a9000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a9100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-c66-memory@a9100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000aa000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-c71-dma-memory@aa000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000aa100000, size 79 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-c71-memory@aa100000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000b2000000, size 96 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-dma-memory@b2000000, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: initialized node vision_apps_shared-memories, compatible id dma-heap-carveout [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000d8000000, size 560 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-core-heap-memory-lo@d8000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fb000000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-virtual-eth-queues@fb000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fb800000, size 24 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-r5f-virtual-eth-buffers@fb800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000880000000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node vision-apps-core-heap-memory-hi@880000000, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000008ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009e7fffff] [ 0.000000] node 0: [mem 0x000000009e800000-0x00000000aeffffff] [ 0.000000] node 0: [mem 0x00000000af000000-0x00000000afffffff] [ 0.000000] node 0: [mem 0x00000000b0000000-0x00000000b7ffffff] [ 0.000000] node 0: [mem 0x00000000b8000000-0x00000000d7ffffff] [ 0.000000] node 0: [mem 0x00000000d8000000-0x00000000fcffffff] [ 0.000000] node 0: [mem 0x00000000fd000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000000880000000-0x000000088fffffff] [ 0.000000] node 0: [mem 0x0000000890000000-0x00000008ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000008ffffffff] [ 0.000000] cma: Reserved 144 MiB at 0x0000000095800000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 31 pages/cpu s88984 r8192 d29800 u126976 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait net.ifnames=0 [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000091800000-0x0000000095800000] (64MB) [ 0.000000] Memory: 2063872K/4194304K available (16896K kernel code, 2218K rwdata, 5216K rodata, 3712K init, 720K bss, 1982976K reserved, 147456K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 960 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001900000 [ 0.000000] ITS [mem 0x01820000-0x0182ffff] [ 0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS [ 0.000000] ITS@0x0000000001820000: Devices Table too large, reduce ids 20->19 [ 0.000000] ITS@0x0000000001820000: allocated 524288 Devices @890800000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x00000008900d0000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000008900e0000 [ 0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns [ 0.000002] sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns [ 0.008522] Console: colour dummy device 80x25 [ 0.013086] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000) [ 0.023755] pid_max: default: 32768 minimum: 301 [ 0.028599] LSM: Security Framework initializing [ 0.033337] Yama: becoming mindful. [ 0.036965] AppArmor: AppArmor initialized [ 0.041150] TOMOYO Linux initialized [ 0.044863] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.052439] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.061488] rcu: Hierarchical SRCU implementation. [ 0.066986] Platform MSI: msi-controller@1820000 domain created [ 0.073437] PCI/MSI: /bus@100000/interrupt-controller@1800000/msi-controller@1820000 domain created [ 0.082816] EFI services will not be available. [ 0.087685] smp: Bringing up secondary CPUs ... [ 0.092994] Detected PIPT I-cache on CPU1 [ 0.093015] GICv3: CPU1: found redistributor 1 region 0:0x0000000001920000 [ 0.093026] GICv3: CPU1: using allocated LPI pending table @0x00000008900f0000 [ 0.093060] CPU1: Booted secondary processor 0x0000000001 [0x411fd080] [ 0.093122] smp: Brought up 1 node, 2 CPUs [ 0.122465] SMP: Total of 2 processors activated. [ 0.127268] CPU features: detected: 32-bit EL0 Support [ 0.132516] CPU features: detected: CRC32 instructions [ 0.156163] CPU: All CPU(s) started at EL2 [ 0.160375] alternatives: patching kernel code [ 0.165539] devtmpfs: initialized [ 0.180815] KASLR disabled due to lack of seed [ 0.185498] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.195477] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.204391] pinctrl core: initialized pinctrl subsystem [ 0.210078] DMI not present or invalid. [ 0.214382] NET: Registered protocol family 16 [ 0.219623] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.226939] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.234995] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.243109] audit: initializing netlink subsys (disabled) [ 0.248791] audit: type=2000 audit(0.160:1): state=initialized audit_enabled=0 res=1 [ 0.249067] thermal_sys: Registered thermal governor 'fair_share' [ 0.256709] thermal_sys: Registered thermal governor 'bang_bang' [ 0.262933] thermal_sys: Registered thermal governor 'step_wise' [ 0.269068] thermal_sys: Registered thermal governor 'user_space' [ 0.275202] thermal_sys: Registered thermal governor 'power_allocator' [ 0.282071] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.295715] ASID allocator initialised with 65536 entries [ 0.324204] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.331065] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.337916] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.344764] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.352557] cryptd: max_cpu_qlen set to 1000 [ 0.358661] raid6: skip pq benchmark and using algorithm neonx8 [ 0.364722] raid6: using neon recovery algorithm [ 0.369890] k3-chipinfo 43000014.chipid: Family:J721E rev:SR2.0 JTAGID[0x1bb6402f] Detected [ 0.378680] vsys_3v3: supplied by evm_12v0 [ 0.383020] vsys_5v0: supplied by evm_12v0 [ 0.387593] iommu: Default domain type: Translated [ 0.392851] SCSI subsystem initialized [ 0.396781] usbcore: registered new interface driver usbfs [ 0.402415] usbcore: registered new interface driver hub [ 0.407853] usbcore: registered new device driver usb [ 0.413290] mc: Linux media interface: v0.10 [ 0.417658] videodev: Linux video capture interface: v2.00 [ 0.423292] pps_core: LinuxPPS API ver. 1 registered [ 0.428363] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.437700] PTP clock support registered [ 0.441718] EDAC MC: Ver: 3.0.0 [ 0.445875] NetLabel: Initializing [ 0.449348] NetLabel: domain hash size = 128 [ 0.453800] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.459606] NetLabel: unlabeled traffic allowed by default [ 0.465617] clocksource: Switched to clocksource arch_sys_counter [ 0.789430] VFS: Disk quotas dquot_6.6.0 [ 0.793488] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.800589] FS-Cache: Loaded [ 0.803721] CacheFiles: Loaded [ 0.807120] AppArmor: AppArmor Filesystem Enabled [ 0.815336] Carveout Heap: Exported 512 MiB at 0x00000000b8000000 [ 0.821681] NET: Registered protocol family 2 [ 0.826409] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.835143] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.844008] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.852419] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [ 0.860157] TCP: Hash tables configured (established 32768 bind 32768) [ 0.867088] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear) [ 0.874756] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.881701] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.889139] NET: Registered protocol family 1 [ 0.894027] RPC: Registered named UNIX socket transport module. [ 0.900081] RPC: Registered udp transport module. [ 0.904884] RPC: Registered tcp transport module. [ 0.909686] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.916267] NET: Registered protocol family 44 [ 0.920810] PCI: CLS 0 bytes, default 64 [ 0.924910] Trying to unpack rootfs image as initramfs... [ 1.212850] Freeing initrd memory: 15400K [ 1.217663] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available [ 1.228441] Initialise system trusted keyrings [ 1.233080] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.241838] zbud: loaded [ 1.245493] NFS: Registering the id_resolver key type [ 1.250730] Key type id_resolver registered [ 1.255001] Key type id_legacy registered [ 1.259138] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.265987] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.273555] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.281132] fuse: init (API version 7.32) [ 1.305340] xor: measuring software checksum speed [ 1.311512] 8regs : 7754 MB/sec [ 1.317045] 32regs : 9061 MB/sec [ 1.322744] arm64_neon : 7895 MB/sec [ 1.327190] xor: using function: 32regs (9061 MB/sec) [ 1.332354] Key type asymmetric registered [ 1.336535] Asymmetric key parser 'x509' registered [ 1.341538] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 1.349167] io scheduler mq-deadline registered [ 1.355254] pinctrl-single 4301c000.pinctrl: 94 pins, size 376 [ 1.361516] pinctrl-single 11c000.pinctrl: 173 pins, size 692 [ 1.370394] k3-ringacc 2b800000.ringacc: Failed to get MSI domain [ 1.376653] k3-ringacc 3c000000.ringacc: Failed to get MSI domain [ 1.384763] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 1.393329] arm-smmu-v3 36600000.iommu: ias 48-bit, oas 48-bit (features 0x00001faf) [ 1.401586] arm-smmu-v3 36600000.iommu: allocated 65536 entries for cmdq [ 1.408654] arm-smmu-v3 36600000.iommu: allocated 32768 entries for evtq [ 1.417044] arm-smmu-v3 36600000.iommu: msi_domain absent - falling back to wired irqs [ 1.429783] brd: module loaded [ 1.561662] loop: module loaded [ 1.565462] megasas: 07.714.04.00-rc1 [ 1.571539] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 1.577967] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.584049] sky2: driver version 1.30 [ 1.588403] VFIO - User Level meta-driver version: 0.3 [ 1.594166] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.600873] ehci-pci: EHCI PCI platform driver [ 1.605738] usbcore: registered new interface driver uas [ 1.611183] usbcore: registered new interface driver usb-storage [ 1.618029] i2c /dev entries driver [ 1.621710] Driver for 1-wire Dallas network protocol. [ 1.626994] DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko [ 1.633948] sdhci: Secure Digital Host Controller Interface driver [ 1.640264] sdhci: Copyright(c) Pierre Ossman [ 1.644921] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.652952] ledtrig-cpu: registered to indicate activity on CPUs [ 1.659292] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.665908] hid: raw HID events driver (C) Jiri Kosina [ 1.671269] usbcore: registered new interface driver usbhid [ 1.676963] usbhid: USB HID core driver [ 1.681340] optee: probing for conduit method. [ 1.685894] optee: revision 3.12 (cac3fef2) [ 1.686142] optee: initialized driver [ 1.695159] drop_monitor: Initializing network drop monitor service [ 1.701958] NET: Registered protocol family 10 [ 1.721205] Segment Routing with IPv6 [ 1.725026] mip6: Mobile IPv6 [ 1.728063] NET: Registered protocol family 17 [ 1.732726] Key type dns_resolver registered [ 1.737097] mpls_gso: MPLS GSO support [ 1.741081] registered taskstats version 1 [ 1.745269] Loading compiled-in X.509 certificates [ 1.750235] zswap: loaded using pool lzo/zbud [ 1.754820] Key type ._fscrypt registered [ 1.758921] Key type .fscrypt registered [ 1.762925] Key type fscrypt-provisioning registered [ 1.771643] Btrfs loaded, crc32c=crc32c-generic [ 1.776367] AppArmor: AppArmor sha1 policy hashing enabled [ 1.786472] k3-ringacc 2b800000.ringacc: Failed to get MSI domain [ 1.792822] k3-ringacc 3c000000.ringacc: Failed to get MSI domain [ 1.801685] ti-sci 44083000.dmsc: ABI: 3.1 (firmware rev 0x0015 '21.9.1--v2021.09a (Terrific Lla') [ 1.859613] omap_i2c 40b00000.i2c: bus 0 rev0.12 at 100 kHz [ 1.865836] omap_i2c 40b10000.i2c: bus 1 rev0.12 at 100 kHz [ 1.872335] at24 2-0050: supply vcc not found, using dummy regulator [ 1.901769] at24 2-0050: 512 byte 24c04 EEPROM, writable, 1 bytes/write [ 1.908562] omap_i2c 42120000.i2c: bus 2 rev0.12 at 400 kHz [ 1.914854] omap_i2c 2000000.i2c: bus 3 rev0.12 at 400 kHz [ 1.921974] omap_i2c 2010000.i2c: bus 4 rev0.12 at 400 kHz [ 1.928226] omap_i2c 2030000.i2c: bus 5 rev0.12 at 400 kHz [ 1.934723] omap_i2c 2050000.i2c: bus 6 rev0.12 at 400 kHz [ 1.941137] ti-sci-intr bus@100000:bus@28380000:interrupt-controller2: Interrupt Router 137 domain created [ 1.951145] ti-sci-intr bus@100000:interrupt-controller0: Interrupt Router 131 domain created [ 1.959951] ti-sci-intr bus@100000:main-navss:interrupt-controller1: Interrupt Router 213 domain created [ 1.969827] ti-sci-inta 33d00000.interrupt-controller: Interrupt Aggregator domain 209 created [ 1.993931] j721e-pcie 2910000.pcie: host bridge /bus@100000/pcie@2910000 ranges: [ 2.001606] j721e-pcie 2910000.pcie: IO 0x0018001000..0x0018010fff -> 0x0018001000 [ 2.009887] j721e-pcie 2910000.pcie: MEM 0x0018011000..0x001fffffff -> 0x0018011000 [ 2.018170] j721e-pcie 2910000.pcie: IB MEM 0x0000000000..0xffffffffffff -> 0x0000000000 [ 2.027513] k3-ringacc 2b800000.ringacc: Ring Accelerator probed rings:286, gp-rings[96,20] sci-dev-id:235 [ 2.037403] k3-ringacc 2b800000.ringacc: dma-ring-reset-quirk: disabled [ 2.044164] k3-ringacc 2b800000.ringacc: RA Proxy rev. 66346100, num_proxies:64 [ 2.053411] k3-ringacc 3c000000.ringacc: Ring Accelerator probed rings:1024, gp-rings[440,150] sci-dev-id:211 [ 2.063564] k3-ringacc 3c000000.ringacc: dma-ring-reset-quirk: disabled [ 2.070323] k3-ringacc 3c000000.ringacc: RA Proxy rev. 66346100, num_proxies:64 [ 2.078313] 40a00000.serial: ttyS1 at MMIO 0x40a00000 (irq = 15, base_baud = 6000000) is a 8250 [ 2.087809] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 27, base_baud = 3000000) is a 8250 [ 2.096561] printk: console [ttyS2] enabled [ 2.096561] printk: console [ttyS2] enabled [ 2.104998] printk: bootconsole [ns16550a0] disabled [ 2.104998] printk: bootconsole [ns16550a0] disabled [ 2.115520] 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 28, base_baud = 3000000) is a 8250 [ 2.124486] 2840000.serial: ttyS6 at MMIO 0x2840000 (irq = 29, base_baud = 3000000) is a 8250 [ 2.141557] [drm] Initialized tidss 1.0.0 20180215 for 4a00000.dss on minor 0 [ 2.148718] tidss 4a00000.dss: [drm] Cannot find any crtc or sizes [ 2.197624] davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 2.209662] davinci_mdio 46000f00.mdio: phy[0]: device 46000f00.mdio:00, driver TI DP83867 [ 2.217975] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00101, cpsw version 0x6BA80100 Ports: 2 quirks:00000000 [ 2.269622] davinci_mdio c000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 2.277183] davinci_mdio c000f00.mdio: no live phy, scanning all [ 2.381715] davinci_mdio c000f00.mdio: timed out waiting for user access [ 2.488510] davinci_mdio c000f00.mdio: timed out waiting for idle [ 2.494601] davinci_mdio: probe of c000f00.mdio failed with error -5 [ 2.500983] am65-cpsw-nuss c000000.ethernet: initializing am65 cpsw nuss version 0x6BA01901, cpsw version 0x6BA80101 Ports: 9 quirks:00000000 [ 2.514737] am65-cpts 310d0000.cpts: CPTS ver 0x4e8a010a, freq:200000000, add_val:4 pps:0 [ 2.526876] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.532374] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 2.540126] xhci-hcd xhci-hcd.0.auto: hcc params 0x200073c9 hci version 0x100 quirks 0x0000002000010010 [ 2.549517] xhci-hcd xhci-hcd.0.auto: irq 221, io mem 0x06410000 [ 2.555714] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 2.563965] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.571170] usb usb1: Product: xHCI Host Controller [ 2.576035] usb usb1: Manufacturer: Linux 5.10.120-ti-arm64-r63 xhci-hcd [ 2.582719] usb usb1: SerialNumber: xhci-hcd.0.auto [ 2.587811] hub 1-0:1.0: USB hub found [ 2.591568] hub 1-0:1.0: 1 port detected [ 2.595640] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.601120] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 2.608763] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.615305] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.623437] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 2.631683] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.638888] usb usb2: Product: xHCI Host Controller [ 2.643752] usb usb2: Manufacturer: Linux 5.10.120-ti-arm64-r63 xhci-hcd [ 2.650438] usb usb2: SerialNumber: xhci-hcd.0.auto [ 2.655496] hub 2-0:1.0: USB hub found [ 2.659249] hub 2-0:1.0: 1 port detected [ 2.765837] mmc0: CQHCI version 5.10 [ 2.774798] gpio gpiochip2: gpio-line-names is length 37 but should be at most length 36 [ 2.783875] vdd_mmc1: supplied by vsys_3v3 [ 2.788891] omap-mailbox 31f80000.mailbox: omap mailbox rev 0x66fc7100 [ 2.795788] omap-mailbox 31f81000.mailbox: omap mailbox rev 0x66fc7100 [ 2.802634] omap-mailbox 31f82000.mailbox: omap mailbox rev 0x66fc7100 [ 2.809483] omap-mailbox 31f83000.mailbox: omap mailbox rev 0x66fc7100 [ 2.810342] mmc0: SDHCI controller on 4f80000.mmc [4f80000.mmc] using ADMA 64-bit [ 2.823492] omap-mailbox 31f84000.mailbox: omap mailbox rev 0x66fc7100 [ 2.833745] j721e-pcie 2910000.pcie: host bridge /bus@100000/pcie@2910000 ranges: [ 2.841232] j721e-pcie 2910000.pcie: IO 0x0018001000..0x0018010fff -> 0x0018001000 [ 2.849311] j721e-pcie 2910000.pcie: MEM 0x0018011000..0x001fffffff -> 0x0018011000 [ 2.857390] j721e-pcie 2910000.pcie: IB MEM 0x0000000000..0xffffffffffff -> 0x0000000000 [ 2.857625] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.896485] mmc0: Command Queue Engine enabled [ 2.900928] mmc0: new HS200 MMC card at address 0001 [ 2.906258] mmcblk0: mmc0:0001 TB2916 14.6 GiB [ 2.910935] mmcblk0boot0: mmc0:0001 TB2916 partition 1 4.00 MiB [ 2.916940] mmcblk0boot1: mmc0:0001 TB2916 partition 2 4.00 MiB [ 2.922942] mmcblk0rpmb: mmc0:0001 TB2916 partition 3 4.00 MiB, chardev (236:0) [ 2.931306] mmcblk0: p1 p2 [ 3.017910] usb 1-1: New USB device found, idVendor=0451, idProduct=8142, bcdDevice= 1.00 [ 3.026080] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=1 [ 3.033199] usb 1-1: SerialNumber: EF050841A4CD [ 3.038186] hub 1-1:1.0: USB hub found [ 3.041953] hub 1-1:1.0: 4 ports detected [ 3.145644] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 3.169850] usb 2-1: New USB device found, idVendor=0451, idProduct=8140, bcdDevice= 1.00 [ 3.178012] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.185577] hub 2-1:1.0: USB hub found [ 3.189342] hub 2-1:1.0: 4 ports detected [ 3.333651] usb 1-1.1: new low-speed USB device number 3 using xhci-hcd [ 3.415368] Console: switching to colour frame buffer device 240x67 [ 3.437876] tidss 4a00000.dss: [drm] fb0: tidssdrmfb frame buffer device [ 3.449896] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00 [ 3.458235] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.465532] usb 1-1.1: Product: USB Keyboard [ 3.469789] usb 1-1.1: Manufacturer: Logitech [ 3.483959] input: Logitech USB Keyboard as /devices/platform/bus@100000/4114000.cdns-usb/6400000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C31C.0001/input/input0 [ 3.557912] hid-generic 0003:046D:C31C.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.0.auto-1.1/input0 [ 3.576546] input: Logitech USB Keyboard Consumer Control as /devices/platform/bus@100000/4114000.cdns-usb/6400000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C31C.0002/input/input1 [ 3.653719] input: Logitech USB Keyboard System Control as /devices/platform/bus@100000/4114000.cdns-usb/6400000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C31C.0002/input/input2 [ 3.670732] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-xhci-hcd.0.auto-1.1/input1 [ 3.761621] usb 1-1.2: new low-speed USB device number 4 using xhci-hcd [ 3.861762] j721e-pcie 2910000.pcie: PCI host bridge to bus 0000:00 [ 3.868023] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.871500] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c050, bcdDevice=27.20 [ 3.873495] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x18001000-0x18010fff]) [ 3.881828] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.891275] pci_bus 0000:00: root bus resource [mem 0x18011000-0x1fffffff] [ 3.898572] usb 1-1.2: Product: USB-PS/2 Optical Mouse [ 3.905444] pci 0000:00:00.0: [104c:b00d] type 01 class 0x060400 [ 3.910542] usb 1-1.2: Manufacturer: Logitech [ 3.916528] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 3.927297] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/bus@100000/4114000.cdns-usb/6400000.usb/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C050.0003/input/input3 [ 3.930571] pci 0000:00:00.0: supports D1 [ 3.947107] hid-generic 0003:046D:C050.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-xhci-hcd.0.auto-1.2/input0 [ 3.950988] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 3.973519] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.985034] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.991654] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.996946] pcieport 0000:00:00.0: PME: Signaling with IRQ 495 [ 4.002973] pcieport 0000:00:00.0: AER: enabled with IRQ 495 [ 4.009583] ti-udma 285c0000.dma-controller: Channels: 26 (tchan: 13, rchan: 13, gp-rflow: 8) [ 4.020598] ti-udma 31150000.dma-controller: Channels: 122 (tchan: 61, rchan: 61, gp-rflow: 16) [ 4.035681] spi-nor spi1.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff [ 4.042561] spi-nor: probe of spi1.0 failed with error -2 [ 4.089640] davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 4.101755] davinci_mdio 46000f00.mdio: phy[0]: device 46000f00.mdio:00, driver TI DP83867 [ 4.110067] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00101, cpsw version 0x6BA80100 Ports: 2 quirks:00000000 [ 4.123894] am65-cpsw-nuss 46000000.ethernet: set new flow-id-base 48 [ 4.130893] am65-cpsw-nuss 46000000.ethernet: initialized cpsw ale version 1.4 [ 4.138104] am65-cpsw-nuss 46000000.ethernet: ALE Table size 64 [ 4.144500] am65-cpsw-nuss 46000000.ethernet: CPTS ver 0x4e8a010a, freq:500000000, add_val:1 pps:0 [ 4.193641] davinci_mdio c000f00.mdio: davinci mdio revision 9.7, bus freq 1000000 [ 4.201200] davinci_mdio c000f00.mdio: no live phy, scanning all [ 4.305685] davinci_mdio c000f00.mdio: timed out waiting for user access [ 4.412486] davinci_mdio c000f00.mdio: timed out waiting for idle [ 4.418579] davinci_mdio: probe of c000f00.mdio failed with error -5 [ 4.424976] am65-cpsw-nuss c000000.ethernet: initializing am65 cpsw nuss version 0x6BA01901, cpsw version 0x6BA80101 Ports: 9 quirks:00000000 [ 4.438760] am65-cpsw-nuss c000000.ethernet: set new flow-id-base 140 [ 4.445701] am65-cpsw-nuss c000000.ethernet: /bus@100000/ethernet@c000000/ethernet-ports/port@1 error retrieving port phy: -19 [ 5.169814] mmc1: CQHCI version 5.10 [ 5.169910] debugfs: Directory 'pd:27' with parent 'pm_genpd' already present! [ 5.180621] debugfs: Directory 'pd:26' with parent 'pm_genpd' already present! [ 5.189030] debugfs: Directory 'pd:242' with parent 'pm_genpd' already present! [ 5.196360] debugfs: Directory 'pd:241' with parent 'pm_genpd' already present! [ 5.203677] debugfs: Directory 'pd:240' with parent 'pm_genpd' already present! [ 5.210982] debugfs: Directory 'pd:239' with parent 'pm_genpd' already present! [ 5.219316] input: gpio-keys as /devices/platform/gpio-keys/input/input4 [ 6.689750] sdhci-am654 4fb0000.mmc: Power on failed [ 6.725307] mmc1: SDHCI controller on 4fb0000.mmc [4fb0000.mmc] using ADMA 64-bit [ 6.735045] Freeing unused kernel memory: 3712K [ 6.758651] Checked W+X mappings: passed, no W+X pages found [ 6.764323] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.427006] remoteproc remoteproc0: b034000.pru is available [ 7.435044] remoteproc remoteproc1: b004000.rtu is available [ 7.453709] remoteproc remoteproc2: b00a000.txpru is available [ 7.459788] remoteproc remoteproc3: b038000.pru is available [ 7.465624] remoteproc remoteproc4: b006000.rtu is available [ 7.471449] remoteproc remoteproc5: b00c000.txpru is available [ 7.477488] remoteproc remoteproc6: b134000.pru is available [ 7.483311] remoteproc remoteproc7: b104000.rtu is available [ 7.489161] remoteproc remoteproc8: b10a000.txpru is available [ 7.495170] remoteproc remoteproc9: b138000.pru is available [ 7.500999] remoteproc remoteproc10: b106000.rtu is available [ 7.506922] remoteproc remoteproc11: b10c000.txpru is available Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -a -C0 /dev/mmcblk0p2 rootfs: clean, 141157/950272 files, 2214199/3794688 blocks done. [ 7.726962] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 7.834938] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 7.955556] systemd[1]: System time before build time, advancing clock. [ 8.003874] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 8.027016] systemd[1]: Detected architecture arm64. Welcome to Debian GNU/Linux 11 (bullseye)! [ 8.036149] systemd[1]: Set hostname to . [ 8.242835] systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. [ 8.315373] systemd[1]: Queued start job for default target Graphical Interface. [ 8.322795] systemd[1]: Unnecessary job for /sys/devices/platform/bus@100000/2800000.serial/tty/ttyS2 was removed. [ 8.333163] systemd[1]: Unnecessary job for /dev/bone/uart/0 was removed. [ 8.341259] random: systemd: uninitialized urandom read (16 bytes read) [ 8.371274] systemd[1]: Created slice system-getty.slice. [ 8.376911] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Created slice system-getty.slice 8.384384] systemd[1]: Created slice system-modprobe.slice. m. [ 8.394861] random: systemd: uninitialized urandom read (16 bytes read) [ OK ] Created slice system-modprobe.slice[ 8.402778] systemd[1]: Created slice system-serial\x2dgetty.slice. . [ OK ] Created slice system-serial\x2dgett[ 8.414410] systemd[1]: Created slice User and Session Slice. y.slice. [ 8.425798] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Created slice User and Session Slic[ 8.434865] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. e. [ OK ] Started Forward Password R[ 8.449538] systemd[1]: Reached target Remote File Systems. …uests to Wall Directory Watch. [ OK ] Set [ 8.460536] systemd[1]: Reached target Slices. up automount Arbitrary…s File System Automount Point 8.470524] systemd[1]: Reached target Swap. [0m. [ OK ] Reached target Remote File Systems. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ 8.496015] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket.[ 8.502043] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communic[ 8.513972] systemd[1]: Listening on initctl Compatibility Named Pipe. ation Socket. [ 8.526419] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on initctl Compatibility [ 8.533483] systemd[1]: Listening on Journal Socket (/dev/log). Named Pipe. [ OK ] Listening on Jour[ 8.544965] systemd[1]: Listening on Journal Socket. nal Audit Socket. [ OK ] Listening on 8.555543] systemd[1]: Listening on Network Service Netlink Socket. 9mJournal Socket (/dev/log). [ OK ] Listening[ 8.567390] systemd[1]: Listening on udev Control Socket. on Journal Socket. [ OK ] Listening[ 8.578207] systemd[1]: Listening on udev Kernel Socket. on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ 8.603398] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System...[ 8.613076] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System..[ 8.625884] systemd[1]: Mounting /sys/kernel/debug... . Mounting /sys/kernel/debug... [ 8.636170] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System...[ 8.647337] systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout..[ 8.658850] systemd[1]: Starting Create list of static device nodes for the current kernel... . Starting Create list of st…odes for the curr[ 8.672835] systemd[1]: Starting Load Kernel Module configfs... ent kernel... Starting Load Kernel Module configfs... [ 8.685480] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm...[ 8.696953] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse...[ 8.706967] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 8.719770] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 8.744886] systemd[1]: Starting Journal Service... Starting Journal Service... [ 8.753964] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 8.763056] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems 8.776183] systemd[1]: Starting Coldplug All udev Devices... [0m... Starting Coldplug All udev Devices... [ 8.788988] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted Huge Pages File System.[ 8.796770] systemd[1]: Mounted POSIX Message Queue File System. [ 8.809758] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ OK ] Mounted POSIX Message Queue File Sy[ 8.818904] systemd[1]: Mounted /sys/kernel/debug. stem. [ 8.828000] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted /sys/kernel/debug. [ 8.835096] systemd[1]: Finished Set the console keyboard layout. [ OK ] Mounted Kernel Trace File System 8.846684] systemd[1]: Finished Create list of static device nodes for the current kernel. m. [ OK ] Finished Set the console keybo[ 8.860173] systemd[1]: modprobe@configfs.service: Succeeded. ard layout. [ OK ] Finished Create l[ 8.870719] systemd[1]: Finished Load Kernel Module configfs. ist of st… nodes for the current kernel. [ OK ] Finished Load Kernel Module configf[ 8.886180] NET: Registered protocol family 36 s. [ 8.902477] systemd[1]: modprobe@drm.service: Succeeded. [ 8.908102] usbcore: registered new interface driver wpanusb [ 8.908479] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 8.926546] systemd[1]: modprobe@fuse.service: Succeeded. [ 8.932971] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse 8.942838] systemd[1]: Finished Remount Root and Kernel File Systems. m. [ 8.948775] gb_bootrom: module is from the staging directory, the quality is unknown, you have been warned. [ OK ] Finished Remount Root and Kernel File Systems. [ 8.974062] greybus: registered new driver bootrom [ 8.979234] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 8.992087] systemd[1]: Mounting Kernel Configuration File System... [ 8.994174] gb_spilib: module is from the staging directory, the quality is unknown, you have been warned. Mounting Kernel Configuration File System.[ 9.009864] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. .. [ 9.024145] gb_firmware: module is from the staging directory, the quality is unknown, you have been warned. [ 9.034288] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 9.044158] greybus: registered new driver gb-firmware [ 9.051213] gb_gbphy: module is from the staging directory, the quality is unknown, you have been warned. [ 9.061401] greybus: registered new driver gbphy [ 9.067835] gb_gpio: module is from the staging directory, the quality is unknown, you have been warned. [ 9.068951] systemd[1]: Starting Load/Save Random Seed... [ 9.082942] gb_gbphy: registered new driver gpio Starting Load/Save Random Seed...[ 9.090346] systemd[1]: Starting Create System Users... Starting Create System Users...[ 9.101402] systemd[1]: Started Journal Service. [ 9.107116] gb_hid: module is from the staging directory, the quality is unknown, you have been warned. [ OK ] Started Journal Service.[ 9.119078] greybus: registered new driver hid [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration F[ 9.141258] gb_i2c: module is from the staging directory, the quality is unknown, you have been warned. ile System. Starting Flush Journal to Persistent Storage... [ 9.166061] gb_gbphy: registered new driver i2c [ OK ] Finished Create System Users.[ 9.177597] gb_log: module is from the staging directory, the quality is unknown, you have been warned. Starting Create Static Device Nodes in /dev... [ 9.198172] systemd-journald[375]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Loca[ 9.216977] greybus: registered new driver log l File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ 9.231776] systemd-journald[375]: File /var/log/journal/1f697aea3c98485b929c361deec7c12b/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 9.251872] gb_loopback: module is from the staging directory, the quality is unknown, you have been warned. [ 9.263177] greybus: registered new driver loopback [ 9.296824] gb_raw: module is from the staging directory, the quality is unknown, you have been warned. [ 9.311142] greybus: registered new driver raw [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Started Rule-based Manager for Device Events and Files. [ 9.346554] gb_spi: module is from the staging directory, the quality is unknown, you have been warned. [ 9.366127] gb_gbphy: registered new driver spi [ 9.382131] gb_uart: module is from the staging directory, the quality is unknown, you have been warned. [ 9.402167] gb_gbphy: registered new driver uart [ OK ] Finished Load Kernel Modules.[ 9.420875] urandom_read_iter: 59 callbacks suppressed [ 9.420878] random: systemd: uninitialized urandom read (16 bytes read) Starting Apply Kernel Variables...[ 9.465821] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Apply Kernel Variables[ 9.507759] random: systemd: uninitialized urandom read (16 bytes read) . Starting Network Service... [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... Starting Show Plymouth Boot Screen... [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ OK ] Started Network Service. [ 9.743270] am65-cpsw-nuss 46000000.ethernet eth0: PHY [46000f00.mdio:00] driver [TI DP83867] (irq=POLL) [ 9.752785] am65-cpsw-nuss 46000000.ethernet eth0: configuring for phy/rgmii-rxid link mode [ OK ] Found device /dev/ttyS2. [ OK ] Reached target Hardware activated USB gadget. [ 10.251564] k3-dsp-rproc 4d80800000.dsp: assigned reserved memory node vision-apps-c66-dma-memory@a9000000 [ 10.322506] k3-dsp-rproc 4d80800000.dsp: configured DSP for remoteproc mode [ 10.340454] ov5640 4-003c: supply DOVDD not found, using dummy regulator [ 10.347354] ov5640 4-003c: supply AVDD not found, using dummy regulator [ 10.354070] ov5640 4-003c: supply DVDD not found, using dummy regulator [ 10.395699] k3-dsp-rproc 4d80800000.dsp: local reset is deasserted for device [ 10.399893] img_enc 4200000.video-encoder: vxe_enc_probe: using heap 1 for internal alloc [ 10.414043] pvrsrvkm: loading out-of-tree module taints kernel. [ 10.423013] remoteproc remoteproc12: 4d80800000.dsp is available [ 10.447169] remoteproc remoteproc12: powering up 4d80800000.dsp [ 10.453193] remoteproc remoteproc12: Booting fw image vision_apps_eaik/vx_app_rtos_linux_c6x_1.out, size 1461044 [ 10.461937] urandom_read_iter: 24 callbacks suppressed [ 10.461940] random: systemd: uninitialized urandom read (16 bytes read) [ 10.475319] random: systemd: uninitialized urandom read (16 bytes read) [ 10.482091] random: systemd: uninitialized urandom read (16 bytes read) [ 10.489194] img_enc 4200000.video-encoder: encoder registered as /dev/video0 [ 10.493055] ov5640 4-003c: ov5640_read_reg: error: reg=300a [ 10.501864] ov5640 4-003c: ov5640_check_chip_id: failed to read chip identifier [ 10.510397] pvrsrvkm 4e20000000.gpu: More than one power domain for this GPU, gpu driver manages power domains [ 10.529543] k3-dsp-rproc 4d81800000.dsp: assigned reserved memory node vision-apps-c66-dma-memory@a8000000 [ 10.531498] k3-dsp-rproc 4d80800000.dsp: booting DSP core using boot addr = 0xa8d9a000 [ 10.578582] k3-dsp-rproc 4d81800000.dsp: configured DSP for remoteproc mode [ 10.600632] PVR_K: 400: Read BVNC 22.104.208.318 from HW device registers [ 10.607588] PVR_K: 400: RGX Device registered with BVNC 22.104.208.318 [ OK ] Found device /dev/mmcblk0p1. Mounting /boot/firmware... [ 10.640185] img_dec 4300000.video-decoder: decoder registered as /dev/video1 [ 10.650728] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ OK ] Mounted /boot/firmware. [ OK ] Reached target Local File Systems. Starting Load AppArmor profiles... Starting Set console font and keymap... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ 10.734817] ov5640: probe of 4-003c failed with error -121 [ 10.747230] k3-dsp-rproc 4d81800000.dsp: local reset is deasserted for device [ 10.749395] remoteproc12#vdev0buffer: assigned reserved memory node vision-apps-c66-dma-memory@a9000000 [ 10.764054] remoteproc12#vdev0buffer: registered virtio0 (type 7) [ 10.770303] remoteproc remoteproc12: remote processor 4d80800000.dsp is now up [ OK ] Finished Set console font and keymap. [ 10.796459] systemd-journald[375]: Failed to read journal file /var/log/journal/1f697aea3c98485b929c361deec7c12b/user-1000.journal for rotation, trying to move it out of the way: Text file busy [ 10.821517] ov5640 6-003c: supply DOVDD not found, using dummy regulator [ 10.828421] ov5640 6-003c: supply AVDD not found, using dummy regulator [ 10.835092] ov5640 6-003c: supply DVDD not found, using dummy regulator [ OK ] Finished Create Volatile Files and Directories. [ 10.856437] remoteproc remoteproc13: 4d81800000.dsp is available Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdo[ 10.873977] remoteproc remoteproc13: powering up 4d81800000.dsp wn... [ 10.875898] random: crng init done [ 10.880024] remoteproc remoteproc13: Booting fw image vision_apps_eaik/vx_app_rtos_linux_c6x_2.out, size 1461012 [ 10.894824] random: 32 urandom warning(s) missed due to ratelimiting [ 10.901836] [drm] Initialized pvr 1.15.6133109 20170530 for 4e20000000.gpu on minor 1 [ 10.909097] audit: type=1400 audit(1659878711.948:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=474 comm="apparmor_parser" [ 10.925039] audit: type=1400 audit(1659878711.948:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=474 comm="apparmor_parser" [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ 10.958550] audit: type=1400 audit(1659878712.000:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=488 comm="apparmor_parser" [ 10.984384] audit: type=1400 audit(1659878712.024:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/aarch64-linux-gnu/lightdm/lightdm-guest-session" pid=475 comm="apparmor_parser" [ 11.003267] audit: type=1400 audit(1659878712.024:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/aarch64-linux-gnu/lightdm/lightdm-guest-session//chromium" pid=475 comm="apparmor_parser" [ 11.013653] k3-dsp-rproc 64800000.dsp: assigned reserved memory node vision-apps-c71-dma-memory@aa000000 [ 11.022981] audit: type=1400 audit(1659878712.052:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=489 comm="apparmor_parser" [ 11.047475] audit: type=1400 audit(1659878712.052:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=489 comm="apparmor_parser" [ 11.062355] audit: type=1400 audit(1659878712.052:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=489 comm="apparmor_parser" [ 11.079382] k3-dsp-rproc 4d81800000.dsp: booting DSP core using boot addr = 0xa9d9a000 [ 11.088103] k3-dsp-rproc 64800000.dsp: configured DSP for remoteproc mode [ 11.095047] remoteproc remoteproc14: 64800000.dsp is available [ OK ] Finished Load AppArmor profiles[ 11.111251] remoteproc13#vdev0buffer: assigned reserved memory node vision-apps-c66-dma-memory@a8000000 . Starting Raise network interfaces...[ 11.121012] remoteproc13#vdev0buffer: registered virtio1 (type 7) [ 11.132548] remoteproc remoteproc13: remote processor 4d81800000.dsp is now up [ 11.134261] ov5640 6-003c: ov5640_read_reg: error: reg=300a [ 11.145477] ov5640 6-003c: ov5640_check_chip_id: failed to read chip identifier [ 11.155225] ov5640: probe of 6-003c failed with error -121 [ 11.211410] remoteproc remoteproc14: powering up 64800000.dsp [ 11.217251] remoteproc remoteproc14: Booting fw image vision_apps_eaik/vx_app_rtos_linux_c7x_1.out, size 13242432 [ 11.227612] remoteproc remoteproc14: unsupported resource 65538 [ 11.237730] k3-dsp-rproc 64800000.dsp: booting DSP core using boot addr = 0xaa200000 [ 11.259649] remoteproc14#vdev0buffer: assigned reserved memory node vision-apps-c71-dma-memory@aa000000 [ 11.263379] omap_rng 4e10000.rng: Random Number Generator ver. 241b34c [ 11.269290] remoteproc14#vdev0buffer: registered virtio2 (type 7) [ 11.281879] remoteproc remoteproc14: remote processor 64800000.dsp is now up [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Docker Socket for the API. [ OK ] Listening on Docker Socket for the API. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD St[ 11.386273] platform 41000000.r5f: R5F core may have been powered on by a different host, programmed state (0) != actual state (1) ack... Starting BeagleBoard.org USB gadgets... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting System Logging Service... Starting User Login Management... Starting LSB: Start daemon at boot time... Starting Disk Manager... Starting WPA supplicant... [ OK ] Finished Raise network interfaces. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started System Logging Service. [ 11.548885] platform 41000000.r5f: configured R5F for IPC-only mode [ 11.555306] using random self ethernet address [ 11.555567] platform 41000000.r5f: assigned reserved memory node vision-apps-r5f-dma-memory@a0000000 [ 11.559765] using random host ethernet address [ 11.574211] remoteproc remoteproc15: 41000000.r5f is available [ 11.580118] remoteproc remoteproc15: attaching to 41000000.r5f [ 11.586196] platform 41000000.r5f: R5F core initialized in IPC-only mode [ OK ] Started Avahi mDNS/DNS-SD Stack[ 11.592918] remoteproc15#vdev0buffer: assigned reserved memory node vision-apps-r5f-dma-memory@a0000000 . [ 11.593038] remoteproc15#vdev0buffer: registered virtio3 (type 7) [ 11.593042] remoteproc remoteproc15: remote processor 41000000.r5f is now attached [ OK ] Started WPA supplicant. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting containerd container runtime... Starting A high performanc… and a reverse proxy server... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [ 11.719162] using random self ethernet address [ 11.719167] using random host ethernet address [ OK ] Finished Permit User Sessions. Starting Light Display Manager... Starting Hold until boot process finishes up... Starting Authorization Manager... [ 11.789411] platform 5c00000.r5f: configured R5F for remoteproc mode [ OK ] Started User Login Management. [ 11.808471] Mass Storage Function, version: 2009/09/11 [ 11.813656] LUN: removable file: (no medium) [ OK ] Started Authorization Manager. [ OK ] Started OpenBSD Secure Shell server. [ 12.002004] Adding 2097148k swap on /var/swap. Priority:-2 extents:16 across:6225916k SSFS [ 12.045253] PVR_K: 681: RGX Firmware image 'rgx.fw.22.104.208.318' loaded [ 12.057587] platform 5c00000.r5f: assigned reserved memory node vision-apps-r5f-dma-memory@a2000000 [ 12.068735] PVR_K: 681: Shader binary image 'rgx.sh.22.104.208.318' loaded [ 12.191670] remoteproc remoteproc16: 5c00000.r5f is available [ 12.202628] remoteproc remoteproc16: powering up 5c00000.r5f [ 12.208329] remoteproc remoteproc16: Booting fw image vision_apps_eaik/vx_app_rtos_linux_mcu2_0.out, size 572788 [ 12.217719] platform 5d00000.r5f: configured R5F for remoteproc mode [ 12.334063] platform 5d00000.r5f: assigned reserved memory node vision-apps-r5f-dma-memory@a4000000 [ 12.335041] remoteproc remoteproc17: 5d00000.r5f is available [ 12.341796] remoteproc remoteproc17: powering up 5d00000.r5f [ 12.360313] remoteproc remoteproc17: Booting fw image vision_apps_eaik/vx_app_rtos_linux_mcu2_1.out, size 297932 [ 12.382294] remoteproc16#vdev0buffer: assigned reserved memory node vision-apps-r5f-dma-memory@a2000000 [ 12.382401] remoteproc16#vdev0buffer: registered virtio4 (type 7) [ 12.382405] remoteproc remoteproc16: remote processor 5c00000.r5f is now up [ 12.402319] platform 5e00000.r5f: configured R5F for remoteproc mode [ 12.402440] remoteproc17#vdev0buffer: assigned reserved memory node vision-apps-r5f-dma-memory@a4000000 [ 12.402537] remoteproc17#vdev0buffer: registered virtio5 (type 7) [ 12.402541] remoteproc remoteproc17: remote processor 5d00000.r5f is now up [ 12.403666] platform 5e00000.r5f: assigned reserved memory node vision-apps-r5f-dma-memory@a6000000 [ 12.404439] remoteproc remoteproc18: 5e00000.r5f is available [ 12.404622] remoteproc remoteproc18: Direct firmware load for j7-main-r5f1_0-fw failed with error -2 [ 12.404631] remoteproc remoteproc18: powering up 5e00000.r5f [ 12.404650] remoteproc remoteproc18: Direct firmware load for j7-main-r5f1_0-fw failed with error -2 [ 12.404653] remoteproc remoteproc18: request_firmware failed: -2 [ 12.405511] platform 5f00000.r5f: configured R5F for remoteproc mode [ 12.407840] platform 5f00000.r5f: assigned reserved memory node vision-apps-r5f-dma-memory@a7000000 [ 12.408389] remoteproc remoteproc19: 5f00000.r5f is available [ 12.408544] remoteproc remoteproc19: Direct firmware load for j7-main-r5f1_1-fw failed with error -2 [ 12.408552] remoteproc remoteproc19: powering up 5f00000.r5f [ 12.408566] remoteproc remoteproc19: Direct firmware load for j7-main-r5f1_1-fw failed with error -2 [ 12.408569] remoteproc remoteproc19: request_firmware failed: -2 [ 12.458734] aufs 5.10.117-20220711 [ 13.359351] audit: type=1400 audit(1664295376.432:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="docker-default" pid=772 comm="apparmor_parser" [ 13.540120] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 13.562155] Bridge firewalling registered [ 13.883516] Initializing XFRM netlink socket [ 14.096501] cdns-csi2rx 4504000.csi-bridge: Probed CSI2RX with 2/4 lanes, 4 streams, external D-PHY [ 14.115416] cdns-csi2rx 4514000.csi-bridge: Probed CSI2RX with 2/4 lanes, 4 streams, external D-PHY [ 14.343067] virtio_rpmsg_bus virtio0: rpmsg host is online [ 14.349074] virtio_rpmsg_bus virtio1: rpmsg host is online [ 14.355072] virtio_rpmsg_bus virtio2: rpmsg host is online [ 14.360964] virtio_rpmsg_bus virtio3: rpmsg host is online [ 14.366931] virtio_rpmsg_bus virtio4: rpmsg host is online [ 14.372897] virtio_rpmsg_bus virtio5: rpmsg host is online [ 14.378547] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0xd [ 14.386569] virtio_rpmsg_bus virtio1: creating channel rpmsg_chrdev addr 0xd [ 14.393806] virtio_rpmsg_bus virtio1: creating channel rpmsg_chrdev addr 0x15 [ 14.401116] virtio_rpmsg_bus virtio1: creating channel ti.ipc4.ping-pong addr 0xe [ 14.409815] virtio_rpmsg_bus virtio2: creating channel rpmsg_chrdev addr 0xd [ 14.417164] virtio_rpmsg_bus virtio2: creating channel rpmsg_chrdev addr 0x15 [ 14.424478] virtio_rpmsg_bus virtio2: creating channel ti.ipc4.ping-pong addr 0xe [ 14.432229] virtio_rpmsg_bus virtio3: creating channel ti.ipc4.ping-pong addr 0xd [ 14.439846] virtio_rpmsg_bus virtio3: creating channel rpmsg_chrdev addr 0xe [ 14.448418] virtio_rpmsg_bus virtio4: creating channel rpmsg_chrdev addr 0xd [ 14.456086] virtio_rpmsg_bus virtio5: creating channel rpmsg_chrdev addr 0xd [ 14.456277] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0x15 [ 14.456466] virtio_rpmsg_bus virtio0: creating channel ti.ipc4.ping-pong addr 0xe [ 14.456889] virtio_rpmsg_bus virtio5: creating channel rpmsg_chrdev addr 0x15 [ 14.457066] virtio_rpmsg_bus virtio5: creating channel ti.ipc4.ping-pong addr 0xe [ 14.457405] virtio_rpmsg_bus virtio4: creating channel rpmsg_chrdev addr 0x15 [ 14.466568] virtio_rpmsg_bus virtio4: creating channel ti.ipc4.ping-pong addr 0xe [ 16.880592] usb0: HOST MAC 24:76:25:a0:d6:cf [ 16.884889] usb0: MAC 24:76:25:a0:d6:d0 [ 16.889149] usb1: HOST MAC 24:76:25:a0:d6:d1 [ 16.893456] usb1: MAC 24:76:25:a0:d6:d2 [ 17.443764] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready [ 17.455205] IPv6: ADDRCONF(NETDEV_CHANGE): usb1: link becomes ready Debian GNU/Linux 11 BeagleBone ttyS2 BeagleBoard.org Debian Bullseye Xfce Image 2022-01-14 Support: https://bbb.io/debian default username:password is [debian:temppwd] BeagleBone login: [ 24.823732] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! [ 27.038165] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! [ 32.827173] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! [ 48.834845] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! BeagleBone login: debian Password: The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Tue Sep 27 16:17:14 UTC 2022 from 192.168.6.1 on pts/1 debian@BeagleBone:~$ [ 80.842508] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! lsusb Bus 002 Device 002: ID 0451:8140 Texas Instruments, Inc. TUSB8041 4-Port Hub Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 004: ID 046d:c050 Logitech, Inc. RX 250 Optical Mouse Bus 001 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 Bus 001 Device 002: ID 0451:8142 Texas Instruments, Inc. TUSB8041 4-Port Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub debian@BeagleBone:~$