Uncompressing Linux................................................................................. ............................................................... done, booting the kernel. Linux version 2.6.28-rc3-omap1 (koen@dominion) (gcc version 4.2.1) #1 Sat Nov 8 09:28:12 CET 2008 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 Beagle Board Memory policy: ECC disabled, Data cache writeback OMAP3430 ES2.1 SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rootdelay=2 rootfstype=ext2 ro video =omapfb:mode:640x480@60 psplash=false Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz GPMC revision 5.0 IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP34xx GPIO hardware version 2.5 PID hash table entries: 512 (order: 9, 2048 bytes) OMAP clockevent source: GPTIMER12 at 32768 Hz Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125084KB available (4092K code, 398K data, 176K init) Calibrating delay loop... 466.36 BogoMIPS (lpj=1822720) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 532 bytes NET: Registered protocol family 16 Found NAND on CS0 Registering NAND on CS0 Unable to get DVI reset GPIO OMAP DMA hardware revision 4.0 USB: No board-specific platform config found OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz twl4030_usb twl4030_usb: Initialized TWL4030 USB module SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb musb_hdrc: version 6.0, musb-dma, host, debug=0 musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Bluetooth: Core ver 2.13 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 244 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 console [ttyS2] enabled brd: module loaded loop: module loaded usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether i2c /dev entries driver input: triton2-pwrbutton as /class/input/input0 triton2 power button driver initialized Driver 'sd' needs updating - please use bus_type methods omap2-nand driver initializing NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit) cmdlinepart partition parsing not available Creating 5 MTD partitions on "omap2-nand": 0x00000000-0x00080000 : "X-Loader" 0x00080000-0x00260000 : "U-Boot" 0x00260000-0x00280000 : "U-Boot Env" 0x00280000-0x00680000 : "Kernel" 0x00680000-0x10000000 : "File System" Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0 twl4030_rtc twl4030_rtc: Power up reset detected. twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC. OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec Bluetooth: HCI USB driver ver 2.10 usbcore: registered new interface driver hci_usb Bluetooth: Broadcom Blutonium firmware driver ver 1.2 usbcore: registered new interface driver bcm203x Bluetooth: Digianswer Bluetooth USB driver ver 0.10 usbcore: registered new interface driver bpa10x Bluetooth: Generic Bluetooth SDIO driver ver 0.1 usb 1-1: new high speed USB device using musb_hdrc and address 2 Registered led device: beagleboard::usr0 Registered led device: beagleboard::usr1 Registered led device: beagleboard::pmu_stat usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18rc3. usbcore: registered new interface driver snd-usb-audio ASoC version 0.13.2 ALSA device list: No soundcards found. oprofile: using arm/armv7 TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 Bluetooth: L2CAP ver 2.11 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.10 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 usb 1-1: configuration #1 chosen from 1 choice RPC: Registered udp transport module. RPC: Registered tcp transport module. ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ThumbEE CPU extension supported. Power Management for TI OMAP3. Unable to set state of powerdomain: sgx_pwrdm Failed to setup powerdomains omap2|3_pm_init failed: -22 hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected SmartReflex driver initialized Disabling unused clock "sr2_fck" ... Disabling unused clock "sys_clkout1" VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 Console: switching to colour frame buffer device 128x48 clock: clksel_round_rate_div: dpll4_m4_ck target_rate 48000000 clock: new_div = 9, new_rate = 48000000 usb 1-1.2: new low speed USB device using musb_hdrc and address 3 twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) Waiting 2sec before mounting root device... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address 0002 mmcblk0: mmc0:0002 7.56 GiB mmcblk0: p1 p2 usb 1-1.2: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /class/input/input1 dell 0003:413C:2105.0001: input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-musb_hdrc-1. 2/input0 usb 1-1.4: new high speed USB device using musb_hdrc and address 4 usb 1-1.4: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 176K INIT: version 2.86 booting Boot splashscreen disabled Starting udevuncorrectable error : <3>uncorrectable error : <3>end_request: I/O error, dev mtdblock0 , sector 0 Buffer I/O error on device mtdblock0, logical block 0 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 8 Buffer I/O error on device mtdblock0, logical block 1 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 16 Buffer I/O error on device mtdblock0, logical block 2 uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 24 Buffer I/O error on device mtdblock0, logical block 3 uncorrectable error : <3>uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0 Buffer I/O error on device mtdblock0, logical block 0 scsi 0:0:0:0: Direct-Access Sony Storage Media 0100 PQ: 0 ANSI: 0 CCS sd 0:0:0:0: [sda] 1014784 512-byte hardware sectors: (519 MB/495 MiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] 1014784 512-byte hardware sectors: (519 MB/495 MiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Attached SCSI removable disk modprobe: FATAL: Could not load /lib/modules/2.6.28-rc3-omap1/modules.dep: No such file or directory tar: can't open '/etc/dev.tar': Read-only file system Remounting root file system... EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended WARNING: Couldn't open directory /lib/modules/2.6.28-rc3-omap1: No such file or directory FATAL: Could not open /lib/modules/2.6.28-rc3-omap1/modules.dep.temp for writing: No such file or di rectory Setting up IP spoofing protection: rp_filter. Configuring network interfaces... modprobe: FATAL: Could not load /lib/modules/2.6.28-rc3-omap1/modu les.dep: No such file or directory ifconfig: SIOCGIFFLAGS: No such device modprobe: FATAL: Could not load /lib/modules/2.6.28-rc3-omap1/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.28-rc3-omap1/modules.dep: No such file or directory eth0 No such device modprobe: FATAL: Could not load /lib/modules/2.6.28-rc3-omap1/modules.dep: No such file or directory udhcpc: SIOCGIFINDEX: No such device done. Starting portmap daemon: portmap. Adding 131064k swap on /swap.file. Priority:-1 extents:34 across:155856k INIT: Entering runlevel: 5 ALSA: Restoring mixer settings... /usr/sbin/alsactl: load_state:1577: No soundcards found... Starting advanced power management daemon: No APM support in kernel (failed.) Starting system message bus: dbus. Starting Hardware abstraction layer hald Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---'