U-Boot SPL 2025.07-g919ec3cd84f3 (Aug 07 2025 - 19:02:03 +0000) SYSFW ABI: 3.1 (firmware rev 0x0015 '21.9.1--v2021.09a (Terrific Lla') Trying to boot from MMC1 Loading Environment from nowhere... OK init_env from device 17 not supported! Starting ATF on ARM64 core... NOTICE: BL31: v2.5(release):0588523 NOTICE: BL31: Built : 16:53:51, Aug 10 2022 U-Boot SPL 2021.01-gf65a2b8f (Aug 10 2022 - 16:53:51 +0000) Model: Texas Instruments K3 J721E SoC ti_i2c_eeprom_am6_get: Invalid board ID record! EEPROM not available at 0x50, trying to read at 0x51 Reading on-board EEPROM at 0x51 failed 1 Board: J721EX-PM1-SOM rev E2 SYSFW ABI: 3.1 (firmware rev 0x0015 '21.9.1--v2021.09a (Terrific Lla') ti_i2c_eeprom_am6_parse_record: Ignoring record id 17 TLB table from ffff4000 to 100000000 SPL malloc() before relocation used 0x2620 bytes (9 KB) >>SPL: board_init_r() spl_init Trying to boot from MMC1 spl: mmc boot mode: fs Jumping to U-Boot loaded - jumping to U-Boot... image entry point: 0x80800000 U-Boot 2021.01-gf65a2b8f (Aug 10 2022 - 16:53:51 +0000) SoC: J721E SR2.0 Model: Texas Instruments K3 J721E SoC Board: BBONEAI-64-B0- rev B0 DRAM: 4 GiB Flash: 0 Bytes MMC: sdhci@4f80000: 0, sdhci@4fb0000: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial@2800000 Out: serial@2800000 Err: serial@2800000 Net: am65_cpsw_nuss_slave ethernet@46000000: K3 CPSW: nuss_ver: 0x6BA00101 cpsw_ver: 0x6BA80100 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000 eth0: ethernet@46000000 Press SPACE to abort autoboot in 2 seconds board_name=[BBONEAI-64-B0-] ... name_fdt=[k3-j721e-beagleboneai64.dtb] ... i2c_write: error waiting for data ACK (status=0x116) pca953x gpio@22: Error reading output register switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 1144 bytes read in 8 ms (139.6 KiB/s) BeagleBone AI-64 microSD (extlinux.conf) (swap enabled) 1: microSD (failsafe) 2: copy microSD to eMMC (default) 3: microSD (debug) 4: microSD Enter choice: 2: copy microSD to eMMC (default) Retrieving file: /initrd.img 14357289 bytes read in 617 ms (22.2 MiB/s) Retrieving file: /Image.gz 14670698 bytes read in 628 ms (22.3 MiB/s) append: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk1p3 ro rootfstype=ext4 rootwait net.ifnames=0 init=/usr/sbin/init-beagle-flasher Retrieving file: /k3-j721e-beagleboneai64.dtb Failed to load '/k3-j721e-beagleboneai64.dtb' Skipping copy microSD to eMMC (default) for failure retrieving fdt 1: microSD (failsafe) Retrieving file: /Image.gz 14670698 bytes read in 628 ms (22.3 MiB/s) append: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk1p3 ro rootfstype=ext4 fsck.repair=yes resume=/dev/mmcblk1p2 rootwait net.ifnames=0 Retrieving file: /k3-j721e-beagleboneai64.dtb Failed to load '/k3-j721e-beagleboneai64.dtb' Skipping microSD (failsafe) for failure retrieving fdt 3: microSD (debug) Retrieving file: /Image.gz 14670698 bytes read in 627 ms (22.3 MiB/s) append: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk1p3 ro rootfstype=ext4 fsck.repair=yes resume=/dev/mmcblk1p2 rootwait net.ifnames=0 Retrieving file: /k3-j721e-beagleboneai64.dtb Failed to load '/k3-j721e-beagleboneai64.dtb' Skipping microSD (debug) for failure retrieving fdt 4: microSD Retrieving file: /Image.gz 14670698 bytes read in 628 ms (22.3 MiB/s) append: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk1p3 ro rootfstype=ext4 fsck.repair=yes resume=/dev/mmcblk1p2 rootwait net.ifnames=0 Retrieving file: /k3-j721e-beagleboneai64.dtb Failed to load '/k3-j721e-beagleboneai64.dtb' Skipping microSD for failure retrieving fdt SCRIPT FAILED: continuing... libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk sdhci@4f80000.blk... Scanning disk sdhci@4fb0000.blk... ** Unrecognized filesystem type ** Found 7 disks No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 209 bytes read in 6 ms (33.2 KiB/s) 1: Linux eMMC Retrieving file: /initrd.img 15594777 bytes read in 92 ms (161.7 MiB/s) Retrieving file: /Image 31642112 bytes read in 179 ms (168.6 MiB/s) append: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait net.ifnames=0 quiet Retrieving file: /k3-j721e-beagleboneai64.dtb 227126 bytes read in 8 ms (27.1 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8f120000, end 8ffff519 ... OK Loading Device Tree to 000000008f0e5000, end 000000008f11f735 ... OK Linux kernel Image start = 0x82000000 end = 0x83ef0000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd080] [ 0.000000] Linux version 5.10.168-ti-arm64-r119 (voodoo@rpi5b8g-64) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1bullseye SMP Thu Aug 7 18:55:48 UTC 2025 [ 0.000000] Machine model: BeagleBoard.org BeagleBone AI-64 [ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.722678] debugfs: Directory '31010000.pat' with parent 'regmap' already present! [ 0.730796] debugfs: Directory '31011000.pat' with parent 'regmap' already present! [ 0.738759] debugfs: Directory '31012000.pat' with parent 'regmap' already present! [ 0.746702] debugfs: Directory '31013000.pat' with parent 'regmap' already present! [ 0.754700] debugfs: Directory '31014000.pat' with parent 'regmap' already present! [ 1.230830] am65-cpsw-nuss c000000.ethernet: /bus@100000/ethernet@c000000/ethernet-ports/port@1 error retrieving port phy: -19 [ 3.141372] debugfs: Directory 'pd:27' with parent 'pm_genpd' already present! [ 3.148619] debugfs: Directory 'pd:26' with parent 'pm_genpd' already present! [ 3.157185] debugfs: Directory 'pd:242' with parent 'pm_genpd' already present! [ 3.164521] debugfs: Directory 'pd:241' with parent 'pm_genpd' already present! [ 3.171826] debugfs: Directory 'pd:240' with parent 'pm_genpd' already present! [ 3.179142] debugfs: Directory 'pd:239' with parent 'pm_genpd' already present! rootfs: clean, 118307/950272 files, 2217008/3794688 blocks [ 7.756952] k3-dsp-rproc 4d80800000.dsp: configured DSP for remoteproc mode [ 7.764713] img_enc 4200000.video-encoder: vxe_enc_probe: using heap 1 for internal alloc [ 7.781182] remoteproc remoteproc12: request_firmware failed: -2 [ 7.792908] k3-dsp-rproc 4d81800000.dsp: configured DSP for remoteproc mode [ 7.962312] remoteproc remoteproc13: request_firmware failed: -2 [ 7.978819] k3-dsp-rproc 64800000.dsp: configured DSP for remoteproc mode [ 7.986369] remoteproc remoteproc14: request_firmware failed: -2 [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Set console font and keymap. [ OK ] Finished Create Volatile Files and Directories. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Finished Raise network interfaces. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... Starting BeagleBoard Generate Symlinks... Starting BeagleBoard.org USB gadgets... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Initialize hardware monitoring sensors... Starting System Logging Service... Starting User Login Management... Starting LSB: Start daemon at boot time... Starting Disk Manager... Starting WPA supplicant... [ 8.769661] platform 41000000.r5f: configured R5F for IPC-only mode [ 8.776918] platform 41000000.r5f: mbox_request_channel failed: -517 [ 8.783305] remoteproc remoteproc15: can't attach to rproc 41000000.r5f: -16 [ 8.829733] k3_r5_rproc bus@100000:bus@28380000:r5fss@41000000: rproc_add failed, ret = -16 [ OK ] Started Network Name Resolution. [ OK ] Reached target Host and Network[ 8.871704] k3_r5_rproc bus@100000:bus@28380000:r5fss@41000000: k3_r5_cluster_rproc_init failed, ret = -16 Name Lookups. [ OK ] Finished Initialize hardware monito[ 8.906193] platform 5c00000.r5f: configured R5F for remoteproc mode ring sensors. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Finished BeagleBoard Generate Symlinks. [ OK ] Started System Logging Service. [ 9.069547] remoteproc remoteproc16: request_firmware failed: -2 [ 9.106270] platform 5d00000.r5f: configured R5F for remoteproc mode [ OK ] Started User Login Management. [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started WPA supplicant. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting LSB: disk temperature monitoring daemon... Starting A high performanc… and a reverse proxy server... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [ 9.282966] remoteproc remoteproc17: request_firmware failed: -2 [ OK ] Started LSB: disk temperature monit[ 9.327784] platform 5e00000.r5f: configured R5F for remoteproc mode oring daemon. [ OK ] Finished Permit User Sessions. Starting Light Display Manager... Starting Hold until boot process finishes up 9.350727] remoteproc remoteproc18: request_firmware failed: -2 0m... [ 9.366638] platform 5f00000.r5f: configured R5F for remoteproc mode [ 9.384082] remoteproc remoteproc19: request_firmware failed: -2 Starting Authorization Manager... [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Authorization Manager. Debian GNU/Linux 11 BeagleBone ttyS2 BeagleBoard.org Debian Bullseye Xfce Image 2022-09-05 Support: https://bbb.io/debian default username:password is [debian:temppwd] BeagleBone login: