CCCC U-Boot SPL 2016.03 (May 17 2017 - 17:44:11) Trying to boot from UART CCCC - CRC mode, 2743(SOH)/0(STX)/0(CAN) packets, 6 retries Loaded 350832 bytes U-Boot 2016.03 (May 17 2017 - 17:44:11 +0530) Watchdog enabled I2C: ready DRAM: 512 MiB board_init Reset Source: Global warm SW reset has occurred. Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 board_late_init Net: cpsw, usb_ether Hit any key to stop autoboot: 5  4  3  2  1  0 Unknown command 'console=ttyO0,115200n8' - try 'help' =>  Unknown command '' - try 'help' => Unknown command '' - try 'help' => Unknown command '' - try 'help' => setenv ipaddr 192.168.10.10 => setenv serverip 192.168.10.11 => setenv netmask 255.255.255.0 => saveenv Saving Environment to MMC... Writing to MMC(1)... done => saveenv setenv netmask 255.255.255.0                            taddr}'" => => run NFS_BOOT; link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.10.11; our IP address is 192.168.10.10 Filename 'vmlinuz-4.4.6-ti-rt-r14'. Load address: 0x80007fc0 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################## 3.1 MiB/s done Bytes transferred = 7159936 (6d4080 hex) link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.10.11; our IP address is 192.168.10.10 Filename 'am335x-boneblack.dtb'. Load address: 0x80f80000 Loading: *############# 2.9 MiB/s done Bytes transferred = 61582 (f08e hex) Kernel image @ 0x80007fc0 [ 0x000000 - 0x6d4080 ] ## Flattened Device Tree blob at 80f80000 Booting using the fdt blob at 0x80f80000 Loading Device Tree to 8ffed000, end 8ffff08d ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.6 (root@Genx3) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT RT Wed May 17 17:53:00 IST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone Black [ 0.000000] cma: Reserved 24 MiB at 0x9e000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (neon ) [ 0.000000] PERCPU: Embedded 14 pages/cpu @df90c000 s25664 r8192 d23488 u57344 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129408 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.10.11:/opt/BPL/nfs_rootfs ip=192.168.10.10:::::eth0 rootfstype=ext4 rootwait fixrtc [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 479536K/522240K available (6793K kernel code, 851K rwdata, 3204K rodata, 536K init, 939K bss, 18128K reserved, 24576K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc09cb7cc (9998 kB) [ 0.000000] .init : 0xc09cc000 - 0xc0a52000 ( 536 kB) [ 0.000000] .data : 0xc0a52000 - 0xc0b26e24 ( 852 kB) [ 0.000000] .bss : 0xc0b29000 - 0xc0c13f20 ( 940 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000022] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000030] OMAP clocksource: timer1 at 24000000 Hz [ 0.000218] Console: colour dummy device 80x30 [ 0.000387] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000390] This ensures that you still see kernel messages. Please [ 0.000393] update your kernel commandline. [ 0.046840] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656) [ 0.046859] pid_max: default: 32768 minimum: 301 [ 0.046996] Security Framework initialized [ 0.047004] Yama: becoming mindful. [ 0.047035] AppArmor: AppArmor disabled by boot time parameter [ 0.047198] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.047205] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.048093] Initializing cgroup subsys io [ 0.048114] Initializing cgroup subsys memory [ 0.048151] Initializing cgroup subsys devices [ 0.048165] Initializing cgroup subsys freezer [ 0.048178] Initializing cgroup subsys net_cls [ 0.048189] Initializing cgroup subsys perf_event [ 0.048200] Initializing cgroup subsys net_prio [ 0.048211] Initializing cgroup subsys pids [ 0.048328] CPU: Testing write buffer coherency: ok [ 0.048337] ftrace: allocating 31297 entries in 62 pages [ 0.133543] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.133725] Setting up static identity map for 0x80008240 - 0x8000828c [ 0.166909] Brought up 1 CPUs [ 0.166933] SMP: Total of 1 processors activated (995.32 BogoMIPS). [ 0.166943] CPU: All CPU(s) started in SVC mode. [ 0.168446] devtmpfs: initialized [ 0.195114] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.221454] omap_hwmod: debugss: _wait_target_disable failed [ 0.275737] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.280663] xor: measuring software checksum speed [ 0.318948] arm4regs : 1221.000 MB/sec [ 0.358878] 8regs : 931.000 MB/sec [ 0.398873] 32regs : 1174.000 MB/sec [ 0.438872] neon : 1690.000 MB/sec [ 0.438883] xor: using function: neon (1690.000 MB/sec) [ 0.438926] pinctrl core: initialized pinctrl subsystem [ 0.441217] NET: Registered protocol family 16 [ 0.445995] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.458921] cpuidle: using governor ladder [ 0.470922] cpuidle: using governor menu [ 0.477344] OMAP GPIO hardware version 0.1 [ 0.492260] No ATAGs? [ 0.492296] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.492700] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.492714] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.599090] raid6: int32x1 gen() 239 MB/s [ 0.666935] raid6: int32x1 xor() 227 MB/s [ 0.734992] raid6: int32x2 gen() 363 MB/s [ 0.802972] raid6: int32x2 xor() 267 MB/s [ 0.870881] raid6: int32x4 gen() 360 MB/s [ 0.938958] raid6: int32x4 xor() 251 MB/s [ 1.007058] raid6: int32x8 gen() 332 MB/s [ 1.074970] raid6: int32x8 xor() 224 MB/s [ 1.142905] raid6: neonx1 gen() 1455 MB/s [ 1.210891] raid6: neonx1 xor() 843 MB/s [ 1.278883] raid6: neonx2 gen() 1773 MB/s [ 1.346887] raid6: neonx2 xor() 1171 MB/s [ 1.414888] raid6: neonx4 gen() 1913 MB/s [ 1.482893] raid6: neonx4 xor() 1185 MB/s [ 1.550916] raid6: neonx8 gen() 876 MB/s [ 1.618887] raid6: neonx8 xor() 794 MB/s [ 1.618898] raid6: using algorithm neonx4 gen() 1913 MB/s [ 1.618907] raid6: .... xor() 1185 MB/s, rmw enabled [ 1.618916] raid6: using intx1 recovery algorithm [ 1.630454] edma 49000000.edma: TI EDMA DMA engine driver [ 1.634841] SCSI subsystem initialized [ 1.639427] usbcore: registered new interface driver usbfs [ 1.639526] usbcore: registered new interface driver hub [ 1.639648] usbcore: registered new device driver usb [ 1.640376] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 1.640431] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe [ 1.640592] pps_core: LinuxPPS API ver. 1 registered [ 1.640602] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.640637] PTP clock support registered [ 1.641664] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 [ 1.644078] NetLabel: Initializing [ 1.644095] NetLabel: domain hash size = 128 [ 1.644103] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.644171] NetLabel: unlabeled traffic allowed by default [ 1.644553] clocksource: Switched to clocksource timer1 [ 1.804757] NET: Registered protocol family 2 [ 1.805640] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 1.805708] TCP bind hash table entries: 4096 (order: 4, 114688 bytes) [ 1.805854] TCP: Hash tables configured (established 4096 bind 4096) [ 1.805937] UDP hash table entries: 256 (order: 2, 16384 bytes) [ 1.805974] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes) [ 1.806256] NET: Registered protocol family 1 [ 1.810956] RPC: Registered named UNIX socket transport module. [ 1.810975] RPC: Registered udp transport module. [ 1.810983] RPC: Registered tcp transport module. [ 1.810992] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.812028] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 1.815085] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.815213] audit: initializing netlink subsys (disabled) [ 1.815286] audit: type=2000 audit(1.748:1): initialized [ 1.829257] zbud: loaded [ 1.829947] VFS: Disk quotas dquot_6.6.0 [ 1.830206] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.837014] NFS: Registering the id_resolver key type [ 1.837082] Key type id_resolver registered [ 1.837092] Key type id_legacy registered [ 1.837123] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.837498] fuse init (API version 7.23) [ 1.838074] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 1.855656] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 1.859956] io scheduler noop registered [ 1.859978] io scheduler deadline registered [ 1.860071] io scheduler cfq registered (default) [ 1.861848] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.863899] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 1.865794] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 1.869741] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 158, base_baud = 3000000) is a 8250 [ 2.732489] console [ttyS0] enabled [ 2.737190] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 159, base_baud = 3000000) is a 8250 [ 2.747044] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 160, base_baud = 3000000) is a 8250 [ 2.812587] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.818732] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.825309] davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe] [ 2.837430] libphy: 4a101000.mdio: probed [ 2.841489] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.851449] cpsw 4a100000.ethernet: Detected MACID = b0:d5:cc:99:9a:c9 [ 2.860449] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.867102] ehci-platform: EHCI generic platform driver [ 2.872656] ehci-omap: OMAP-EHCI Host Controller driver [ 2.878421] usbcore: registered new interface driver usblp [ 2.884030] usbcore: registered new interface driver usb-storage [ 2.891969] 47401300.usb-phy supply vcc not found, using dummy regulator [ 2.911305] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver [ 2.917120] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 1 [ 2.925262] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.932088] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.939346] usb usb1: Product: MUSB HDRC host driver [ 2.944336] usb usb1: Manufacturer: Linux 4.4.6 musb-hcd [ 2.949674] usb usb1: SerialNumber: musb-hdrc.0.auto [ 2.955696] hub 1-0:1.0: USB hub found [ 2.959519] hub 1-0:1.0: 1 port detected [ 2.973481] 47401b00.usb-phy supply vcc not found, using dummy regulator [ 3.002321] mousedev: PS/2 mouse device common for all mice [ 3.009198] omap_rtc 44e3e000.rtc: already running [ 3.014520] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 3.023055] i2c /dev entries driver [ 3.028346] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 3.036391] omap_hsmmc 48060000.mmc: Got CD GPIO [ 3.074944] omap_hsmmc 48060000.mmc: card busy [ 3.080925] omap_hsmmc 48060000.mmc: card busy [ 3.106159] hidraw: raw HID events driver (C) Jiri Kosina [ 3.112686] usbcore: registered new interface driver usbhid [ 3.116573] omap_hsmmc 481d8000.mmc: card busy [ 3.122766] usbhid: USB HID core driver [ 3.126858] omap_hsmmc 481d8000.mmc: card busy [ 3.131491] ashmem: initialized [ 3.135607] remoteproc0: wkup_m3 is available [ 3.142980] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 3.154884] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 3.172968] NET: Registered protocol family 10 [ 3.174392] mmc1: MAN_BKOPS_EN bit is not set [ 3.177890] mmc1: new high speed MMC card at address 0001 [ 3.188499] mmcblk0: mmc1:0001 Q2J54A 3.64 GiB [ 3.197683] mmcblk0boot0: mmc1:0001 Q2J54A partition 1 2.00 MiB [ 3.201135] mip6: Mobile IPv6 [ 3.201156] NET: Registered protocol family 17 [ 3.201331] Key type dns_resolver registered [ 3.201341] mpls_gso: MPLS GSO support [ 3.201561] omap_voltage_late_init: Voltage driver support not added [ 3.202427] PM: Cannot get wkup_m3_ipc handle [ 3.202526] ThumbEE CPU extension supported. [ 3.202551] Registering SWP/SWPB emulation handler [ 3.203793] registered taskstats version 1 [ 3.203961] zswap: loaded using pool lzo/zbud [ 3.217643] Btrfs loaded [ 3.236861] Key type encrypted registered [ 3.250651] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 3.274272] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 3.274863] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.275132] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 3.281798] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.282263] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.282727] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.283180] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 3.283222] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 3.289199] remoteproc0: powering up wkup_m3 [ 3.289216] remoteproc0: Booting fw image am335x-pm-firmware.elf, size 219735 [ 3.289685] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 [ 3.289701] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19) [ 3.290104] PM: bootloader does not support rtc-only! [ 3.290638] omap_rtc 44e3e000.rtc: setting system clock to 2016-05-26 08:51:06 UTC (1464252666) [ 3.290653] of_cfs_init [ 3.290806] of_cfs_init: OK [ 3.296946] remoteproc0: remote processor wkup_m3 is now up [ 3.297000] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x191 [ 3.308972] net eth0: initializing cpsw version 1.12 (0) [ 3.311358] net eth0: phy found : id is : 0x7c0f1 [ 3.325304] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.431082] mmcblk0boot1: mmc1:0001 Q2J54A partition 2 2.00 MiB [ 7.341190] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 7.348621] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.364756] IP-Config: Guessing netmask 255.255.255.0 [ 7.370047] IP-Config: Complete: [ 7.373301] device=eth0, hwaddr=b0:d5:cc:99:9a:c9, ipaddr=192.168.10.10, mask=255.255.255.0, gw=255.255.255.255 [ 7.383873] host=192.168.10.10, domain=, nis-domain=(none) [ 7.389823] bootserver=255.255.255.255, rootserver=192.168.10.11, rootpath= [ 7.410135] VFS: Mounted root (nfs filesystem) on device 0:16. [ 7.416727] devtmpfs: mounted [ 7.420465] Freeing unused kernel memory: 536K (c09cc000 - c0a52000) [ 7.715251] random: systemd urandom read with 61 bits of entropy available [ 7.741609] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 7.755596] systemd[1]: Detected architecture 'arm'. Welcome to Debian GNU/Linux 8 (jessie)! [ 7.775227] systemd[1]: Set hostname to . [ 8.003795] systemd-fstab-generator[112]: Failed to create mount unit file /run/systemd/generator/-.mount, as it already exists. Duplicate entry in /etc/fstab? [ 8.086387] systemd[111]: /lib/systemd/system-generators/systemd-fstab-generator failed with error code 1. [ 8.462169] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 8.470710] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 8.478486] systemd[1]: Expecting device dev-ttyS0.device... Expecting device dev-ttyS0.device... [ 8.492968] systemd[1]: Starting Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). [ 8.504893] systemd[1]: Reached target Remote File Systems (Pre). [ 8.511163] systemd[1]: Starting Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 8.524891] systemd[1]: Reached target Encrypted Volumes. [ 8.530526] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch. [ 8.539060] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 8.547272] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point. [ OK ] Set up automount Arbitrary Executable File Formats F...utomount Point. [ 8.568864] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 8.578469] systemd[1]: Starting Swap. [ OK ] Reached target Swap. [ 8.588881] systemd[1]: Reached target Swap. [ 8.593300] systemd[1]: Starting Root Slice. [ OK ] Created slice Root Slice. [ 8.604868] systemd[1]: Created slice Root Slice. [ 8.609727] systemd[1]: Starting User and Session Slice. [ OK ] Created slice User and Session Slice. [ 8.624904] systemd[1]: Created slice User and Session Slice. [ 8.630813] systemd[1]: Starting Delayed Shutdown Socket. [ OK ] Listening on Delayed Shutdown Socket. [ 8.644898] systemd[1]: Listening on Delayed Shutdown Socket. [ 8.650795] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 8.668880] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 8.675994] systemd[1]: Starting Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.688891] systemd[1]: Listening on Journal Socket (/dev/log). [ 8.695044] systemd[1]: Starting udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.708898] systemd[1]: Listening on udev Control Socket. [ 8.714509] systemd[1]: Starting udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.732875] systemd[1]: Listening on udev Kernel Socket. [ 8.738372] systemd[1]: Starting Journal Socket. [ OK ] Listening on Journal Socket. [ 8.748881] systemd[1]: Listening on Journal Socket. [ 8.754114] systemd[1]: Starting System Slice. [ OK ] Created slice System Slice. [ 8.764925] systemd[1]: Created slice System Slice. [ 8.770770] systemd[1]: Started File System Check on Root Device. [ 8.777088] systemd[1]: Starting system-getty.slice. [ OK ] Created slice system-getty.slice. [ 8.788961] systemd[1]: Created slice system-getty.slice. [ 8.794537] systemd[1]: Starting system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 8.808920] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 8.815588] systemd[1]: Starting Increase datagram queue length... Starting Increase datagram queue length... [ 8.839479] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 8.943755] random: nonblocking pool is initialized [ 8.955316] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required static device nodes...rrent kernel... [ 9.038502] systemd[1]: Mounted Huge Pages File System. [ 9.100103] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 9.145710] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 9.207641] systemd[1]: Started Set Up Additional Binary Formats. [ 9.227509] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 9.294872] systemd[1]: Starting Slices. [ OK ] Reached target Slices. [ 9.333627] systemd[1]: Reached target Slices. [ 9.341188] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ OK ] Mounted POSIX Message Queue File System. [ 9.433180] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ 9.461184] systemd[1]: Mounted Debug File System. [ OK ] Started Increase datagram queue length. [ 9.489174] systemd[1]: Started Increase datagram queue length. [ 9.513152] systemd[1]: systemd-modules-load.service: main process exited, code=exited, status=1/FAILURE [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ 9.585098] systemd[1]: Failed to start Load Kernel Modules. [ 9.592426] systemd[1]: Unit systemd-modules-load.service entered failed state. [ OK ] Started Create list of required static device nodes ...current kernel. [ 9.633151] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 9.678891] systemd[1]: systemd-remount-fs.service: main process exited, code=exited, status=1/FAILURE [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. [ 9.745110] systemd[1]: Failed to start Remount Root and Kernel File Systems. [ 9.760768] systemd[1]: Unit systemd-remount-fs.service entered failed state. [ OK ] Started udev Coldplug all Devices. [ 9.921012] systemd[1]: Started udev Coldplug all Devices. [ 10.101214] systemd[1]: Started Various fixups to make systemd work better on Debian. [ 10.109265] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... [ 10.126598] systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... [ 10.172262] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 10.218883] systemd[1]: Mounting Configuration File System... Mounting Configuration File System... [ 10.303293] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 10.380102] systemd[1]: Starting Syslog Socket. [ OK ] Listening on Syslog Socket. [ 10.417242] systemd[1]: Listening on Syslog Socket. [ 10.430536] systemd[1]: Starting Journal Service... Starting Journal Service... [ OK ] Started Journal Service. [ 10.489852] systemd[1]: Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Configuration File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Reached target Remote File Systems. Starting Trigger Flushing of Journal to Persistent Storage... [ 11.049804] systemd-udevd[217]: starting version 215 Starting LSB: Raise network interfaces.... [ OK ] Started udev Kernel Device Manager. [ 11.517200] systemd-journald[208]: Received request to flush runtime journal from PID 1 [ OK ] Started Trigger Flushing of Journal to Persistent Storage. Starting Copy rules generated while the root was ro... Starting LSB: Tune IDE hard disks... [ OK ] Started Copy rules generated while the root was ro. [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started LSB: Tune IDE hard disks. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Found device /dev/ttyS0. [ OK ] Started LSB: Raise network interfaces.. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target System Initialization. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on CUPS Printing Service Sockets. [ OK ] Reached target Sockets. [ OK ] Reached target Timers. [ OK ] Reached target Paths. [ OK ] Reached target Basic System. Starting Restore /etc/resolv.conf if the system cras...s shut down.... Starting Generic Board Startup... Starting OpenBSD Secure Shell server... [ OK ] Started OpenBSD Secure Shell server. Starting Regular background program processing daemon... [ OK ] Started Regular background program processing daemon. Starting Cape Manager Service... Starting /etc/rc.local Compatibility... Starting LSB: Start busybox udhcpd at boot time... Starting LSB: Load kernel modules needed to enable cpufreq scaling... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Apache2 web server... Starting Login Service... Starting Avahi mDNS/DNS-SD Stack... Starting D-Bus System Message Bus... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Avahi mDNS/DNS-SD Stack. Starting System Logging Service... Starting Permit User Sessions... Starting CUPS Printing Service... [ OK ] Started CUPS Printing Service. Starting Make remote CUPS printers available locally... [ OK ] Started Make remote CUPS printers available locally. [ OK ] Started Restore /etc/resolv.conf if the system crash...was shut down.. [ OK ] Started Cape Manager Service. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started LSB: Start busybox udhcpd at boot time. [ OK ] Started LSB: Advanced IEEE 802.11 management daemon. [ OK ] Started Permit User Sessions. [ OK ] Started System Logging Service. [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling. [ 18.502585] g_multi: unknown parameter '192.168.10.11:/opt/BPL/nfs_rootf1' ignored [ 18.654066] using random self ethernet address [ 18.658670] using random host ethernet address [ 18.687002] using host ethernet address: B0:D5:CC:99:9A:CB [ 18.729868] using self ethernet address: B0:D5:CC:99:9A:C0[ 18.849003] Mass Storage Function, version: 2009/09/11 [ 18.858348] LUN: removable file: (no medium) [ 18.875775] lun0: unable to open backing file: /dev/nfs [ 18.910434] g_multi musb-hdrc.1.auto: failed to start g_multi: -2 [ OK ] Started Login Service. Starting LSB: set CPUFreq kernel parameters... Starting Getty on tty1... [ OK ] Started Getty on tty1. Starting Serial Getty on ttyS0... [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: set CPUFreq kernel parameters. Expecting device dev-ttyGS0.device... [ OK ] Started LSB: Apache2 web server. Debian GNU/Linux 8 arm ttyS0 default username:password is [debian:temppwd] The IP Address for eth0 is: 192.168.10.10 arm login: root (automatic login) Last login: Thu May 26 08:44:51 UTC 2016 on ttyS0 Linux arm 4.4.6 #1 SMP PREEMPT RT Wed May 17 17:53:00 IST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@arm:~# flashFlash.sh Thu May 26 08:51:57 UTC 2016 /dev/mmcblk0 Flashing uboot................ 10+0 records in 10+0 records out 10485760 bytes (10 MB) copied, 0.964735 s, 10.9 MB/s 0+1 records in 0+1 records out 74180 bytes (74 kB) copied, 0.0255975 s, 2.9 MB/s 0+1 records in 0+1 records out 350896 bytes (351 kB) copied, 0.0818751 s, 4.3 MB/s Flashing FS................ Welcome to fdisk (util-linux 2.25.2). Changes will remain in memory only, until you decide to write them. Be careful before using the write command. Device does not contain a recognized partition table. Created a new DOS disklabel with disk identifier 0x3628886b. Command (m for help): No partition is defined yet! Could not delete partition 3069262673 Command (m for help): Partition type p primary (0 primary, 0 extended, 4 free) e extended (container for logical partitions) Select (default p): Partition number (1-4, default 1): First sector (2048-7634943, default 2048): Last sector, +sectors or +size{K,M,G,T,P} (4096-7634943, default 7634943): Created a new partitio[ 55.743201] mmcblk0: p1 n 1 of type 'Linux' and of size 3.7 GiB. Command (m for help): The partition table has been altered. Calling ioctl() to re-read partition table. Syncing disks. Flashing emmc mke2fs 1.42.12 (29-Aug-2014) Discarding device blocks: 4096/953856528384/953856 done Creating filesystem with 953856 4k blocks and 238560 inodes Filesystem UUID: ab936900-852d-4347-b393-bbe3a13bc839 Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Allocating group tables: 0/30 done Writing inode tables: 0/30 done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: 0/30 done Flashing Debian in eMMC................ [ 64.390129] loop: module loaded [ 64.592297] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 64.717401] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) Thu May 26 08:56:19 UTC 2016 root@arm:~# reboot Starting Synchronise Hardware Clock to System Clock... [ OK ] Stopped target System Time Synchronized. Stopping User Manager for UID 0... [ OK ] Stopped target Multi-User System. Stopping Make remote CUPS printers available locally... Stopping OpenBSD Secure Shell server... Stopping Regular background program processing daemon... Stopping LSB: Start busybox udhcpd at boot time... Stopping LSB: Advanced IEEE 802.11 management daemon... Stopping LSB: set CPUFreq kernel parameters... Stopping LSB: Apache2 web server... [ OK ] Stopped target Login Prompts. Stopping Getty on tty1... Stopping Serial Getty on ttyS0... Stopping D-Bus System Message Bus... Stopping System Logging Service... [ OK ] Stopped OpenBSD Secure Shell server. [ OK ] Stopped Regular background program processing daemon. [ OK ] Stopped Avahi mDNS/DNS-SD Stack. [ OK ] Stopped D-Bus System Message Bus. [ OK ] Stopped Make remote CUPS printers available locally. [ OK ] Stopped Getty on tty1. [ OK ] Stopped System Logging Service. [ OK ] Stopped Serial Getty on ttyS0. [ OK ] Stopped User Manager for UID 0. [ OK ] Stopped LSB: Start busybox udhcpd at boot time. [ OK ] Stopped LSB: Advanced IEEE 802.11 management daemon. [ OK ] Stopped LSB: set CPUFreq kernel parameters. [ OK ] Started Synchronise Hardware Clock to System Clock. Stopping LSB: Load kernel modules needed to enable cpufreq scaling... Stopping Login Service... [ OK ] Removed slice user-0.slice. [ OK ] Removed slice system-serial\x2dgetty.slice. [ OK ] Removed slice system-getty.slice. Stopping /etc/rc.local Compatibility... [ OK ] Stopped /etc/rc.local Compatibility. Stopping Permit User Sessions... Stopping CUPS Printing Service... [ OK ] Stopped Login Service. [ OK ] Stopped LSB: Load kernel modules needed to enable cpufreq scaling. [ OK ] Stopped Permit User Sessions. [ OK ] Stopped CUPS Printing Service. [ OK ] Stopped LSB: Apache2 web server. [ OK ] Stopped target Basic System. [ OK ] Stopped target Slices. [ OK ] Removed slice User and Session Slice. [ OK ] Stopped target Paths. [ OK ] Stopped target Timers. [ OK ] Stopped target Sockets. [ OK ] Closed Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Closed D-Bus System Message Bus Socket. [ OK ] Closed Syslog Socket. [ OK ] Closed CUPS Printing Service Sockets. [ OK ] Stopped target System Initialization. Stopping Network Time Synchronization... Stopping Apply Kernel Variables... [ OK ] Stopped Apply Kernel Variables. Stopping Update UTMP about System Boot/Shutdown... [ OK ] Stopped target Encrypted Volumes. [ OK ] Stopped target Swap. [ OK ] Stopped target Network is Online. [ OK ] Stopped target Network. Stopping LSB: Raise network interfaces.... [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). [ OK ] Stopped Network Time Synchronization. [ OK ] Stopped Update UTMP about System Boot/Shutdown. [ OK ] Stopped LSB: Raise network interfaces.. Stopping Load/Save Random Seed... Stopping Create Volatile Files and Directories... [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped target Local File Systems. Unmounting /run/user/0... [ OK ] Stopped Load/Save Random Seed. [ OK ] Unmounted /run/user/0. [ OK ] Reached target Unmount All Filesystems. [ OK ] Stopped target Local File Systems (Pre). Stopping Create Static Device Nodes in /dev... [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Reached target Shutdown. [ 706.113302] watchdog watchdog0: watchdog did not stop! [ 706.161682] systemd-shutdown[1]: Sending SIGTERM to remaining processes... [ 706.202899] systemd-journald[208]: Received SIGTERM from PID 1 (systemd-shutdow). [ 706.226106] systemd-shutdown[1]: Sending SIGKILL to remaining processes... [ 706.263711] systemd-shutdown[1]: Hardware watchdog 'OMAP Watchdog', version 0 [ 706.273784] systemd-shutdown[1]: Unmounting file systems. [ 706.281352] systemd-shutdown[1]: Unmounting /sys/fs/fuse/connections. [ 706.296887] systemd-shutdown[1]: Unmounting /sys/kernel/config. [ 706.312696] systemd-shutdown[1]: Unmounting /dev/mqueue. [ 706.328686] systemd-shutdown[1]: Unmounting /sys/kernel/debug. [ 706.357522] systemd-shutdown[1]: All filesystems unmounted. [ 706.363242] systemd-shutdown[1]: Deactivating swaps. [ 706.368856] systemd-shutdown[1]: All swaps deactivated. [ 706.374258] systemd-shutdown[1]: Detaching loop devices. [ 706.383233] systemd-shutdown[1]: All loop devices detached. [ 706.389004] systemd-shutdown[1]: Detaching DM devices. [ 706.395528] systemd-shutdown[1]: All DM devices detached. [ 706.405990] systemd-shutdown[1]: Rebooting. [ 706.433084] musb-hdrc musb-hdrc.0.auto: remove, state 4 [ 706.438460] usb usb1: USB disconnect, device number 1 [ 706.444422] musb-hdrc musb-hdrc.0.auto: USB bus 1 deregistered [ 706.451210] reboot: Restarting system U-Boot SPL 2016.03 (May 17 2017 - 17:44:11) Trying to boot from MMC Card did not respond to voltage select! *** Warning - MMC init failed, using default environment U-Boot 2016.03 (May 17 2017 - 17:44:11 +0530) Watchdog enabled I2C: ready DRAM: 512 MiB board_init Reset Source: Global warm SW reset has occurred. Reset Source: Power-on reset has occurred. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 board_late_init Net: cpsw, usb_ether Hit any key to stop autoboot: 5  4  3  2  1  0 Unknown command 'console=ttyO0,115200n8' - try 'help' =>