Linux version 2.6.32-14362-g340cc2b-dirty (voodoo@ubuntu-lvrm) (gcc version 4.3.1 (GCC) ) #1 PREEMPT Wed Dec 16 20:01:00 CST 2009
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Beagle Board
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat c042a4f0, node_mem_map c0447000
  Normal zone: 512 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 65024 pages, LIFO batch:15
OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro vram=12M omapfb.mode=dvi:1280x720MR-16@60
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 243072KB available (3764K code, 314K data, 148K init, 0K highmem)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
console [tty0] enabled
Calibrating delay loop... 490.52 BogoMIPS (lpj=1916928)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
mux: Setting signal i2c3_scl.i2c3_scl 0x0118 -> 0x0100
mux: Setting signal i2c3_sda.i2c3_sda 0x0118 -> 0x0100
mux: Setting signal hdq_sio.gpio170 0x001c -> 0x0104
mux: Setting signal etk_clk.hsusb1_stp 0x001b -> 0x0003
mux: Setting signal etk_ctl.hsusb1_clk 0x0013 -> 0x0003
mux: Setting signal etk_d8.hsusb1_dir 0x0113 -> 0x010b
mux: Setting signal etk_d9.hsusb1_nxt 0x0113 -> 0x010b
mux: Setting signal etk_d0.hsusb1_data0 0x0113 -> 0x010b
mux: Setting signal etk_d1.hsusb1_data1 0x0113 -> 0x010b
mux: Setting signal etk_d2.hsusb1_data2 0x0113 -> 0x010b
mux: Setting signal etk_d7.hsusb1_data3 0x0113 -> 0x010b
mux: Setting signal etk_d4.hsusb1_data4 0x0113 -> 0x010b
mux: Setting signal etk_d5.hsusb1_data5 0x0113 -> 0x010b
mux: Setting signal etk_d6.hsusb1_data6 0x0113 -> 0x010b
mux: Setting signal etk_d3.hsusb1_data7 0x0113 -> 0x010b
mux: Setting signal etk_d11.hsusb2_stp 0x0013 -> 0x0003
mux: Setting signal etk_d10.hsusb2_clk 0x0013 -> 0x0003
mux: Setting signal etk_d12.hsusb2_dir 0x0113 -> 0x010b
mux: Setting signal etk_d13.hsusb2_nxt 0x0113 -> 0x010b
mux: Setting signal etk_d14.hsusb2_data0 0x0113 -> 0x010b
mux: Setting signal etk_d15.hsusb2_data1 0x0113 -> 0x010b
mux: Setting signal mcspi1_cs3.hsusb2_data2 0x0113 -> 0x010b
mux: Setting signal mcspi2_cs1.hsusb2_data3 0x0113 -> 0x010b
mux: Setting signal mcspi2_simo.hsusb2_data4 0x0113 -> 0x010b
mux: Setting signal mcspi2_somi.hsusb2_data5 0x0113 -> 0x010b
mux: Setting signal mcspi2_cs0.hsusb2_data6 0x0113 -> 0x010b
mux: Setting signal mcspi2_clk.hsusb2_data7 0x0113 -> 0x010b
Found NAND on CS0
Registering NAND on CS0
Unable to get DVI reset GPIO
mux: Setting signal sdrc_cke0.sdrc_cke0 0x0118 -> 0x0000
mux: Setting signal sdrc_cke1.sdrc_cke1 0x0118 -> 0x0000
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
mux: Setting signal etk_d9.gpio23 0x010b -> 0x0104
mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0018 -> 0x0118
mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat4.sdmmc1_dat4 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat5.sdmmc1_dat5 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat6.sdmmc1_dat6 0x0118 -> 0x0118
mux: Setting signal sdmmc1_dat7.sdmmc1_dat7 0x0118 -> 0x0118
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine (X), bulk split (X), HB-ISO Rx, HB-ISO Tx, SoftConn)
musb_hdrc: MHDRC RTL version 1.400 
musb_hdrc: setup fifo_mode 4
musb_hdrc: 28/31 max ep, 16384/16384 memory
musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 475
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
usbcore: registered new interface driver asix
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
usb 1-1: new high speed USB device using musb_hdrc and address 2
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
hub 1-1:1.0: USB hub found
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Power Management for TI OMAP3.
hub 1-1:1.0: 4 ports detected
Disabling unused clock "sr2_fck"
Disabling unused clock "sr1_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
Disabling unused clock "gpt6_ick"
Disabling unused clock "gpt7_ick"
Disabling unused clock "gpt8_ick"
Disabling unused clock "gpt9_ick"
Disabling unused clock "wdt3_ick"
Disabling unused clock "wdt3_fck"
Disabling unused clock "gpio2_dbck"
Disabling unused clock "gpio3_dbck"
Disabling unused clock "gpio4_dbck"
Disabling unused clock "gpio5_dbck"
Disabling unused clock "gpio6_dbck"
Disabling unused clock "gpt9_fck"
Disabling unused clock "gpt8_fck"
Disabling unused clock "gpt7_fck"
Disabling unused clock "gpt6_fck"
Disabling unused clock "gpt5_fck"
Disabling unused clock "gpt4_fck"
Disabling unused clock "gpt3_fck"
Disabling unused clock "gpt2_fck"
Disabling unused clock "gpt1_ick"
Disabling unused clock "wdt1_ick"
Disabling unused clock "wdt2_ick"
Disabling unused clock "wdt2_fck"
Disabling unused clock "gpio1_dbck"
Disabling unused clock "gpt1_fck"
Disabling unused clock "cam_ick"
Disabling unused clock "cam_mclk"
Disabling unused clock "des1_ick"
Disabling unused clock "sha11_ick"
Disabling unused clock "rng_ick"
Disabling unused clock "aes1_ick"
Disabling unused clock "ssi_ick"
Disabling unused clock "mailboxes_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "mcbsp_ick"
Disabling unused clock "gpt10_ick"
Disabling unused clock "gpt11_ick"
Disabling unused clock "i2c_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "mcspi_ick"
Disabling unused clock "hdq_ick"
Disabling unused clock "mspro_ick"
Disabling unused clock "des2_ick"
Disabling unused clock "sha12_ick"
Disabling unused clock "aes2_ick"
Disabling unused clock "icr_ick"
Disabling unused clock "pka_ick"
Disabling unused clock "ssi_ssr_fck"
Disabling unused clock "hdq_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcspi_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "mcbsp_fck"
Disabling unused clock "i2c_fck"
Disabling unused clock "mspro_fck"
Disabling unused clock "gpt11_fck"
Disabling unused clock "gpt10_fck"
Disabling unused clock "sad2d_ick"
Disabling unused clock "dpll4_m6x2_ck"
Disabling unused clock "dpll3_m3x2_ck"
Disabling unused clock "sys_clkout1"
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
fbcvt: 1280x720@60: CVT Name - .921M9-R
Console: switching to colour frame buffer device 160x45
regulator_init_complete: incomplete constraints, leaving VDAC on
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Waiting for root device /dev/mmcblk0p2...
usb 1-1.4: new low speed USB device using musb_hdrc and address 3
input: CHICONY USB Keyboard as /devices/platform/musb_hdrc/usb1/1-1/1-1.4/1-1.4:1.0/input/input0
generic-usb 0003:04F2:0116.0001: input: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-musb_hdrc-1.4/input0
mmc0: new high speed SDHC card at address 1234
mmcblk0: mmc0:1234 SA04G 3.68 GiB 
 mmcblk0: p1 p2 p3 < p5 >
EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 179:2.
Freeing init memory: 148K
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal