U-Boot SPL 2011.12 (Apr 02 2012 - 16:20:33) Texas Instruments Revision detection unimplemented OMAP SD/MMC: 0 timed out in wait_for_bb: I2C_STAT=1000 reading u-boot.img reading u-boot.img U-Boot 2011.12 (Apr 02 2012 - 16:20:33) OMAP3630/3730-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 512 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0 *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Beagle xM Rev C No EEPROM on expansion board Die ID #7ba600029ff800000160a7450701600c Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 The user button is currently NOT pressed. SD/MMC found on device 0 reading uEnv.txt 134 bytes read Loaded environment from uEnv.txt Importing environment from mmc ... reading uImage 3200328 bytes read Booting from mmc ... ## Booting kernel from Legacy Image at 80300000 ... Image Name: Linux-3.2.9 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3200264 Bytes = 3.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.2.9 (iv233417@medjerda) (gcc version 4.4.6 (crosstool-NG 1.14.1) ) #1 SMP PREEMPT Mon Apr 2 16:53:09 CEST 2012 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0fc2000 s10400 r8192 d14176 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyO2,115200n8 noinitrd mpurate=auto buddy=none camera=none vram=12M omapfb.mode=dvi:640x480MR-16@60 t [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 507728k/507728k available, 16560k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc04baa84 (4811 kB) [ 0.000000] .init : 0xc04bb000 - 0xc05ea8a0 (1215 kB) [ 0.000000] .data : 0xc05ec000 - 0xc0673230 ( 541 kB) [ 0.000000] .bss : 0xc0673254 - 0xc0bb9b04 (5403 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:410 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001251] Calibrating delay loop... 500.97 BogoMIPS (lpj=1953792) [ 0.072113] pid_max: default: 32768 minimum: 301 [ 0.073181] Security Framework initialized [ 0.073638] Mount-cache hash table entries: 512 [ 0.080047] CPU: Testing write buffer coherency: ok [ 0.081420] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.118469] Brought up 1 CPUs [ 0.118499] SMP: Total of 1 processors activated (500.97 BogoMIPS). [ 0.123779] devtmpfs: initialized [ 0.151916] print_constraints: dummy: [ 0.155364] NET: Registered protocol family 16 [ 0.157501] GPMC revision 5.0 [ 0.178344] OMAP GPIO hardware version 2.5 [ 0.204040] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.207275] OMAP3 Beagle Rev: xM C [ 0.235198] Reprogramming SDRC clock to 400000000 Hz [ 0.235229] dpll3_m2_clk rate change failed: -22 [ 0.237182] Found NAND on CS0 [ 0.237213] Registering NAND on CS0 [ 0.239074] Unable to get DVI reset GPIO [ 0.314575] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.345153] omap-mcbsp.2: alias fck already exists [ 0.346771] omap-mcbsp.3: alias fck already exists [ 0.358489] OMAP DMA hardware revision 5.0 [ 0.465454] bio: create slab at 0 [ 0.481872] SCSI subsystem initialized [ 0.498596] usbcore: registered new interface driver usbfs [ 0.501037] usbcore: registered new interface driver hub [ 0.502838] usbcore: registered new device driver usb [ 0.508300] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz [ 0.525085] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 0.525970] twl4030: power (irq 373) chaining IRQs 376..383 [ 0.529541] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 0.532531] _omap_mux_init_gpio: Could not set gpio192 [ 0.545867] print_constraints: VMMC1: 1850 <--> 3150 mV at 3150 mV normal standby [ 0.549926] print_constraints: VDAC: 1800 mV normal standby [ 0.554107] print_constraints: VDVI: 1800 mV normal standby [ 0.558654] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby [ 0.559967] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz [ 0.579864] Switching to clocksource 32k_counter [ 0.817138] NET: Registered protocol family 2 [ 0.818572] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.821746] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.822540] TCP bind hash table entries: 16384 (order: 7, 655360 bytes) [ 0.833160] TCP: Hash tables configured (established 16384 bind 16384) [ 0.833374] TCP reno registered [ 0.833435] UDP hash table entries: 256 (order: 2, 24576 bytes) [ 0.833801] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes) [ 0.835266] NET: Registered protocol family 1 [ 0.893310] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.065704] msgmni has been set to 991 [ 1.139953] io scheduler noop registered [ 1.140014] io scheduler deadline registered [ 1.140380] io scheduler cfq registered (default) [ 1.143798] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.207489] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 1.221527] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 1.237121] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 [ 1.818267] console [ttyO2] enabled [ 1.838684] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3 [ 1.935882] brd: module loaded [ 1.982330] loop: module loaded [ 1.998229] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.006317] omap2-nand driver initializing [ 2.011566] No NAND device found [ 2.015167] No NAND device found [ 2.020172] OneNAND driver initializing [ 2.042236] usbcore: registered new interface driver asix [ 2.049774] usbcore: registered new interface driver cdc_ether [ 2.057342] usbcore: registered new interface driver net1080 [ 2.065063] usbcore: registered new interface driver cdc_subset [ 2.072387] usbcore: registered new interface driver zaurus [ 2.078765] cdc_ncm: 04-Aug-2011 [ 2.083465] usbcore: registered new interface driver cdc_ncm [ 2.094482] usbcore: registered new interface driver cdc_wdm [ 2.100830] Initializing USB Mass Storage driver... [ 2.107391] usbcore: registered new interface driver usb-storage [ 2.114105] USB Mass Storage support registered. [ 2.121337] usbcore: registered new interface driver libusual [ 2.129058] usbcore: registered new interface driver usbtest [ 2.138305] twl_rtc twl_rtc: Power up reset detected. [ 2.145141] twl_rtc twl_rtc: Enabling TWL-RTC. [ 2.156677] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 2.167633] i2c /dev entries driver [ 2.178192] Driver for 1-wire Dallas network protocol. [ 2.191131] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.199890] twl4030_wdt twl4030_wdt: Failed to register misc device [ 2.207000] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 2.465515] usbcore: registered new interface driver usbhid [ 2.471862] usbhid: USB HID core driver [ 2.475891] oprofile: hardware counters not available [ 2.481475] oprofile: using timer interrupt. [ 2.487121] TCP cubic registered [ 2.490539] Initializing XFRM netlink socket [ 2.495452] NET: Registered protocol family 17 [ 2.500579] NET: Registered protocol family 15 [ 2.505432] Registering the dns_resolver key type [ 2.511627] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.520019] ThumbEE CPU extension supported. [ 2.590667] clock: disabling unused clocks to save power [ 2.605468] regulator_init_complete: VDVI: incomplete constraints, leaving on [ 2.617218] regulator_init_complete: VDAC: incomplete constraints, leaving on [ 2.632537] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.647644] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.664550] Freeing init memory: 1212K minimal_init[ 2.721649] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.739929] mmc0: new high speed SDHC card at address 23fa [ 2.763519] mmcblk0: mmc0:23fa SD04G 3.69 GiB [ 2.787200] mmcblk0: p1 p2