U-Boot SPL 2015.07-rc2-00001-g15e7184 (Jun 09 2015 - 09:01:57) U-Boot 2015.07-rc2-00001-g15e7184 (Jun 09 2015 - 09:01:57 -0500), Build: jenkins-github_Bootloader-Builder-163 Watchdog enabled I2C: ready DRAM: 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Using default environment Net: not set. Validating first E-fuse MAC cpsw Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 Card did not respond to voltage select! Card did not respond to voltage select! gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 switch to partitions #0, OK mmc1(part 0) is current device gpio: pin 54 (gpio 54) value is 1 Checking for: /uEnv.txt ... Checking for: /boot.scr ... Checking for: /boot/boot.scr ... Checking for: /boot/uEnv.txt ... gpio: pin 55 (gpio 55) value is 1 581 bytes read in 28 ms (19.5 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... gpio: pin 56 (gpio 56) value is 1 Running uname_boot ... loading /boot/vmlinuz-3.14.43-ti-r67 ... 7131184 bytes read in 419 ms (16.2 MiB/s) loading /boot/dtbs/3.14.43-ti-r67/am335x-boneblack.dtb ... 87161 bytes read in 95 ms (895.5 KiB/s) loading /boot/initrd.img-3.14.43-ti-r67 ... 3634409 bytes read in 224 ms (15.5 MiB/s) debug: [console=ttyO0,115200n8 root=UUID=31351a87-5c24-4001-a9b2-5570ab2cfd4d ro rootfstype=ext4 rootwait fixrtc coherent_pool=1M quiet] ... debug: [bootz 0x82000000 0x88080000:3774e9 0x88000000] ... Kernel image @ 0x82000000 [ 0x000000 - 0x6cd030 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8fc88000, end 8ffff4e9 ... OK Loading Device Tree to 8fc6f000, end 8fc87478 ... OK Starting kernel ... [ 0.000421] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000429] This ensures that you still see kernel messages. Please [ 0.000436] update your kernel commandline. [ 2.815689] musb-hdrc musb-hdrc.0.auto: Failed to request rx1. [ 2.821653] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517 [ 2.895540] musb-hdrc musb-hdrc.1.auto: Failed to request rx1. [ 2.901494] musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517 [ 3.052473] cpu cpu0: cpu0 clock notifier not ready, retry [ 3.061903] Error: Driver 'tfp410' is already registered, aborting... [ 3.070198] slave hdmi: could not get i2c [ 7.616589] mmcblk0: timed out sending r/w cmd command, card status 0xe00 [ 7.623492] end_request: I/O error, dev mmcblk0, sector 421752 [ 7.629366] Buffer I/O error on device mmcblk0p1, logical block 52463 [ 7.635998] EXT4-fs (mmcblk0p1): error loading journal mount: mounting /dev/disk/by-uuid/31351a87-5c24-4001-a9b2-5570ab2cfd4d on /root failed: Invalid argument mount: mounting /dev on /root/dev failed: No such file or directory mount: mounting /sys on /root/sys failed: No such file or directory mount: mounting /proc on /root/proc failed: No such file or directory Target filesystem doesn't have requested /sbin/init. No init found. Try passing init= bootarg. BusyBox v1.21.1 (Ubuntu 1:1.21.0-1ubuntu1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)